Claude (Anthropic), at the direction of Robert
Drzyzgula
Development Build v83, November 2026
1 Introduction
About this guide. VSM Base was designed and tested by Robert
Drzyzgula. This guide was written by Claude, an AI model made by
Anthropic, at his direction, from the design, his measurements and
photographs, and his builds. Claude also wrote most of the OpenSCAD
code, again at his direction. Please report errors as issues on the
project’s GitHub repository.
VSM Base is a parametric model of a portable, hinged base for vintage
flatbed sewing machines. You give it measurements of your machine’s bed
casting; it produces a base whose seat, hinge recesses and clearances
fit that casting, and that prints in two halves on an ordinary desktop
printer.
1.1 What has been tested
Only a small part of what the model can make has been printed and
used. Treat everything else as untested on a real
printer: it has been checked in the model, but not built.
Tested, on a Singer 99K (the default machine profile), printed in
PETG:
the base in its default form: split into two halves with the
dovetail keys and mending plates, the storage compartment, the handholds
and harness rods;
the back, left and corner extensions with their hinged lids, the
printed extension pegs (tapped into the lips with a hammer; they then
mate with the base’s holes), and the extended back lip;
the lollipop hinges, mounted with 1” #8-32 screws and nylon-insert
locknuts in the nut traps; the mending plates, held by 1/2” #8-32
flat-head screws into nylon-insert locknuts in their traps (the screws
push through the printed membranes);
the organizer insert test parts (bobbin_test,
notion_test) and the full stack of five bobbin trays; a
spool tray and a divided notion tray for the back bay. On the spool
tray, in silk PLA, a curb split from the floor at the first layer above
it; the gussets and taller curb added since have not been printed
yet.
These were printed from development versions of the model as it
evolved, not from the current one: later changes (the split joint’s
serrations, for one) have not all been printed yet.
Not yet tested, among others: other machines and custom profiles; the
base printed in one piece; the outlet, knee-controller and controller
compartments; the freestanding boxes, the standalone bobbin box, the
motor test rig and the attached bay; a base without hinges; the printed
hinge; flush beds, beds on their feet, recessed lips, trims and the cord
slot; the Kenmore 158-14001 profile; the turn button; the ruler and
logos on the front face, and the logos on the back and bottom; pin or
molded extension pegs; the pass-through cover; and every option set away
from its default. The knee controller and the motor-control paper’s
designs have not been built at all.
If you build something from the untested list, please report how it
went as an issue on the project’s GitHub repository.
1.2 Why this exists
Many vintage sewing machines were sold built into cabinets and
tables. Today few people have room for a sewing table, and a machine
without a portable base is hard to use, to store, or even to give away.
Too many good machines are scrapped for that reason alone.
Collectors make their own bases, and a few small makers sell them.
The difficult part is the hinge recesses and the fit of the bed: they
need careful work with a router and chisels, and so most homemade bases
are boxes the machine simply sits in. The shops and skills for that kind
of work are becoming scarce. 3D printers, on the other hand, are now
common and inexpensive, and a printer is very good at exactly the
precise, repeatable shapes that are hard to make by hand.
The model is published under the MIT license so that nobody has to
repeat the work. It is only useful, though, if it works the first time:
a full base is a long print and a lot of filament. This guide is written
to make that likely. It asks you to measure carefully, to read what the
model tells you about your numbers, and to print a few small test parts
before the real thing.
1.3 How to use this guide
Work through the chapters in order the first time:
What you need: printer, filament, software and
hardware.
Measuring your machine: the measurements the model
needs, how to take them, and a worked example for the Singer 99K.
Configuring the model: the Customizer, which
settings matter for fit, and how to read the console output.
Test parts: what each one checks, what a good
result looks like, and what to adjust if it isn’t.
Printing: orientation, supports, and the features
that are removed or drilled out after printing.
Assembly: plates, nuts, hinges, rods, extensions
and lids.
Other machines and hinges: adapting the model and
contributing a profile.
The last chapter is a reference listing every parameter in the model.
It is generated from the model’s own comments, so it always matches the
code.
1.4 Conventions
Directions. Directions are given as you sit at the
machine to sew. Front is the side nearest you and back
is the hinge side. On most flatbed machines, including the Singer 99,
the needle is at the left end and the pillar and handwheel are
at the right.
Units. Measurements of the machine’s bed are entered
in inches, because vintage castings were designed in
fractional inches and are easiest to measure that way; enter them as
decimals (12 3/16” is 12.1875). Everything else in the
model, including the casting reliefs and bobbin trenches, is in
millimetres. Each parameter’s description says
which.
Parameter names are shown like
bed_length_in. They are the names you will see in
OpenSCAD’s Customizer and in the parameter reference.
Coordinates. Inside the model, X runs from left to
right, Y from front to back and Z upward, with the origin at the base’s
outer front-left bottom corner. You only need this if you read the
code.
2 What you need
This chapter is an outline, still to be written. It will
cover:
Printer: build volume needed for each part, and how to check it with
printer_size.
Filament: PETG (tested), why not PLA for a base that may sit in a
warm room or a car, and how much to allow.
Software: OpenSCAD 2021.01 or later, installing BOSL2, and a
slicer.
Hardware list with quantities and sources: hinges, mending plates,
screws, nuts, rods, cushions.
Tools: calipers, drill bits for the membranes, pliers for the
knock-out walls.
3 Measuring your machine
This is the most important chapter in the guide. Every critical
dimension of the base is computed from a handful of measurements of your
machine’s bed casting. If they are right, the base fits; if one is
wrong, the base will be wrong in a way no amount of printer tuning can
fix.
3.1 Measure the casting, not an old
base
If your machine came in an old wooden base, it is tempting to copy
that. Don’t. Wooden bases were hand-fitted, they shrink and wear over
decades, and many have been swapped between machines: a base that came
with your 99 may have been made for a 128, or fitted by eye in a shop
sixty years ago. The cast-iron bed of the machine has not changed since
it left the factory. Measure that.
3.2 Tools
Calipers (dial or digital), 6” or larger. These are
essential for everything under an inch: plate thickness, hole position,
hole diameter and the thickness of the casting’s bosses.
A steel rule, 12” or longer, graduated in 32nds or
64ths, for the bed’s length and width.
A small square is useful for measuring the
hinge-hole height.
Paper and pencil. Write every number down as you measure it; the worksheet at the end of this chapter
has a place for each one.
Measure everything at least twice. Where the guide asks for the same
measurement at both ends of the bed, take both and compare them.
3.3 Getting ready
Remove the machine from any base or cabinet, take off the motor belt
guard or anything else that hangs below the bed if it’s easy to remove,
and work on a clean, flat table. Several measurements are easiest with
the machine on its back (hinge side down) or upside down on a towel.
Fractions to decimals, for entering the bed measurements:
16ths
inch
16ths
inch
16ths
inch
16ths
inch
1/16
0.0625
5/16
0.3125
9/16
0.5625
13/16
0.8125
1/8
0.125
3/8
0.375
5/8
0.625
7/8
0.875
3/16
0.1875
7/16
0.4375
11/16
0.6875
15/16
0.9375
1/4
0.25
1/2
0.5
3/4
0.75
1
1.0
3.4 The bed outline
Top view of the bed. The bed is the flat
casting the machine’s arm stands on; its outline sets the size of the
seat in the base.
3.4.1 Bed length,
bed_length_in
Measure the bed from end to end, left to right, along its top
surface. Measure along a straight part of the edge, not across the
rounded corners, and read the rule at the very ends of the casting, not
at any paint lip or decal.
The base’s seat is made bed_clearance (0.75 mm) larger
than the bed on each side, so the bed drops in without binding. Don’t
add your own allowance: enter what you measure.
3.4.2 Bed width,
bed_width_in
Measure the bed from front to back in the same way, near the middle
of the bed where the front and back edges are straight.
3.4.3 Plate thickness,
bed_plate_thickness_in
The bed is a flat plate with a skirt and bosses cast underneath.
Measure the thickness of the flat plate with calipers at a front edge or
an end, away from any thickened area. On the Singer 99 it is 5/16”.
The plate thickness, together with the hinge-hole height below,
determines how deep the hinge pins must sit in the base, so it has to be
right.
3.5 The hinge holes
If your machine has no hinges, or you’d rather build a plain base
for it to sit in, set hinge_type = "none" and skip this
section; see the note on bases without hinges in Configuring the
model.
The machine pivots on two pins that enter holes in the rear skirt of
the bed. The model places the hinge recesses so that the pins line up
with those holes exactly, both along the back and in height.
Rear of a Singer 99K bed, with a rule
along the back. The hinge holes are the two holes in the rear skirt, one
near each end.
3.5.1 Hole position,
hinge_hole_inset_in
Measure from each end of the bed to the center of
the nearer hinge hole. The center can’t be measured directly, so measure
from the end of the bed to the near edge of the hole and to the far
edge, and average the two; or measure to the near edge and add half the
hole’s diameter.
Do this at both ends. The model assumes the holes are the same
distance from each end. On the 99 they are 1 7/16” from each end.
Check your work. Also measure the distance between
the two hole centers. The two insets plus the spacing between the holes
must add up to the bed length:
inset + spacing + inset = length
On the 99: 1 7/16” + 9 5/16” + 1 7/16” = 12 3/16”. ✓
If they don’t add up, measure again before going any further. If the
two insets really differ by more than about 1/32”, the model’s symmetric
placement won’t fit your machine; see the chapter on other machines.
3.5.2 Hole height,
hinge_hole_drop_in
Measure how far the center of the hinge hole is
below the top surface of the bed. With the machine on
its back, lay a small square or a straightedge across the bed’s top
surface where it overhangs the hole, and measure from it to the top and
bottom edges of the hole; the center is halfway between. On the 99 it is
3/8”.
Section through the back edge at a hinge
hole. On the 99 the hole sits below the flat plate, in a thickened
boss.
3.5.3 Hole diameter
Measure the hinge holes’ diameter. For lollipop hinges it isn’t a
model parameter, but it is the diameter of the hinge pins you need. For
the printed hinge it sets the steel pin’s diameter
(custom_hinge_pin_d_mm): choose rod just under the hole’s
size, so the pin slides in without play. On the 99 the holes are 9/32”
(7.14 mm; worn ones measure up to 7.2 mm), and set screws in the casting
clamp the pins; on the Kenmore 158-14001, 6 mm. Measure how deep the
holes go too (custom_hinge_hole_depth_mm; the shallower
one, if they differ): that limits how long the printed hinge’s pin may
be, and the console then gives the pin lengths that fit. Without a stock
length, the pin enters the holes by
custom_hinge_pin_engage_mm (12 mm on the 99K, 16 mm on the
Kenmore).
3.5.4 Bed cushions,
bed_cushion_in
Most bases have small rubber or felt cushions under the corners of
the bed, which quiet the machine and keep it from rocking. The model
lifts the bed by their thickness when it works out the hinge height.
Enter the thickness of your cushions when compressed under the
machine’s weight; the default is 1/16”. If you use no cushions, enter
0.
Fit the cushions before you check anything against the machine:
without them the bed sits lower than the model expects, and the
extensions will stand proud of it. Cushions also vary in how much they
compress. Once the base is printed and the machine sits in it on its
cushions, lay a straightedge from the bed onto an extension (or its top
slice from the test parts). If the extension is high or low, set
ext_top_adjust to the difference (negative lowers it); it
moves the whole extension top plane, lids, lips and bobbin trenches
together.
Once these numbers are entered, the console reports the height of the
bed’s hole axis and the height of the hinge pins’ axis. They must agree:
if they differ by more than a quarter of a millimetre the model prints a
WARNING. Fix that before printing anything.
3.6 Thickened areas of the casting,
bed_reliefs
Around its edge, the bed rests on a ledge in the base. Most castings
are thickened in places along the edge: bosses around the hinge holes,
ribs at the ends, lugs for screws. Wherever the casting hangs below the
flat plate over the ledge, the ledge must be cut away under it, or the
bed won’t sit down. These cut-aways are the
reliefs.
Underside of a Singer 99K. The flat
plate, the rear skirt with the hinge bosses, and the thickened centers
of each end are visible around the edge.How the thickened areas are measured.
Each one becomes an entry in bed_reliefs.
Turn the machine upside down and look along each edge. For each place
where the casting is deeper than the flat plate within about 10 mm
(3/8”) of the edge, measure:
Which edge it is on: "left",
"right", "back" or "front".
Where it starts and where it ends along that edge.
Measure along the back and front edges from the bed’s left end,
and along the left and right ends from the bed’s front edge.
The center is halfway between the start and the end,
and the length is the end minus the start.
How thick the casting is there, measured from the
bed’s top surface down to the lowest point of the boss. At the edge of
the bed you can usually reach both surfaces with the outside jaws of the
calipers.
The left end of a Singer 99K from below,
showing the thickened center of the end.
bed_reliefs is in millimetres (inches ×
25.4). Each entry is [edge, center, length, thickness], and
the whole setting is a list of entries:
The model makes each relief a little bigger than you measured: 2 mm
longer at each end (relief_margin) and 1 mm deeper
(relief_clearance). You don’t need to add your own
allowance, but when an edge is hard to see, it is better to measure
generously than tightly. A relief that is too big is invisible once the
machine is in the base; one that is too small stops the bed from
seating.
The console lists each relief with its position and depth, so you can
check that it landed where you meant.
3.7 Room under the bed
The base’s cavity has to clear everything that hangs below the bed:
the hook or shuttle drive, the feed mechanism, the shafts and their
bearings. With the defaults, the cavity is about 295 × 152 mm in plan,
set 8 mm in from the bed’s edge all round (bed_ledge), and
there are about 75 mm (just under 3”) from the bed’s top surface to the
cavity floor.
With the machine upside down, lay a straightedge across the bottom of
the bed and measure how far the lowest part of the mechanism stands
above it; add the plate thickness to get its depth below the bed’s top
surface. Check, too, that nothing hangs below the bed within 8 mm of its
edge except the bosses you entered as reliefs. If anything is too deep,
increase inner_depth; if anything is too close to the edge,
reduce bed_ledge or add a relief.
The center slice in the test parts (see the chapter on test parts)
has the full inside profile of the base, and is the best check: slide it
along the underside of the machine and see that nothing touches.
A machine that stands on cast feet under the casting can be carried
on them instead (see a bed set flush, or standing on its feet
in Configuring the model): stand it on a flat surface and measure from
the surface to the plate’s underside, for
custom_foot_height_mm. To find where the feet are, print
the foot-locating rig (foot_rig_left and
foot_rig_right, bolted together with eight M3 bolts through
the splice tabs): a thin box 80 mm tall that fits round the bed, with a
narrow floor rim, an open bottom, and a floor bar across each half to
keep it square, rig_bar_in (100 mm) in from each end of the
bed; set that where no foot can land. Each half also prints with a thin
tie across its open end, to hold its walls against warping on the
printer; snap it off at its necks before bolting the halves together.
Print with a brim, or your slicer’s mouse-ear brim at the corners;
rig_ears adds ears to the part itself for a slicer that has
none. Screw it to a board over a sheet of paper, mark the paper through
the six small holes in the floor rim (each 5 mm in from the bed’s edges,
at the corners and at the split; the console lists their exact
positions), ink the feet, and lower the machine into the box. Measure
each foot’s print from the marks. The rig is cut for the machine profile
in use, with a notch for its cords if it has a cord slot. Everything
else under the bed must then be shorter than the feet; the Kenmore
158-14001’s feet are 63 mm. Note, too, anything that leaves the casting
through its edge, such as a cord, for custom_cord_slot.
In place of plain paper, tools/make_foot_rig_sheet.py
draws a full-size target sheet for the rig, from the same profile: a
millimeter grid in light blue over the bed’s footprint, with coordinates
every 10 mm, the rig’s outline, its marking holes as crosshairs to sight
through, its screw holes, and four corner markers for squaring up a
photograph. It needs a large-format printer, about 545 × 335 mm for the
Kenmore, and must print at 100%: a 200 mm scale bar on the sheet checks
that. Ink the feet black, so they stand out from the blue grid.
3.8 The bobbin cover,
left_trench and back_trench
On drop-in bobbin machines the bobbin is reached through a slide
plate in the bed, which slides out past the edge of the casting. The
base itself doesn’t get in its way, because the bed stands above the
base’s top surface. The extensions, though, are level with the bed, so
an extension on that side needs a shallow trench for the plate to slide
into.
A Singer 99K’s slide plate pulled open.
It slides out past the left end of the bed.Seen edge-on, the plate stays level with
the bed’s top surface as it slides past the edge of the
casting.How the bobbin-plate trench is
measured.
Measure, in millimetres:
Center: the middle of the plate across its width,
from the bed’s front edge (for left_trench) or from the
bed’s left end (for back_trench).
Width: the plate’s width plus about 1 mm of
clearance each side.
Length: how far past the edge of the casting the
plate must slide to uncover the bobbin, plus a margin. Allow at least
1/4” more than you measure.
Depth: the plate’s thickness plus about 0.5
mm.
On the Singer 99 the plate is 2 3/16” wide, centered on the left end,
2 mm thick, and slides about 1 1/4” past the casting, giving
left_trench = [83.34, 57.6, 40, 2.5]. On the Singer 128 the
plate slides toward the back, and back_trench is used
instead. Set a trench to [] if your machine doesn’t need
one.
3.9 Worked example: Singer 99K
These are the defaults in the model, measured from a 1950s Singer
99K. Your 99 should be very close, but measure it anyway.
Every measurement on this machine is an odd number of sixteenths of
an inch, and the hinge-hole check adds up exactly: a good sign that the
numbers are right.
3.10 Checking your numbers
After entering your measurements, render the base (F5) and read the
console. In particular:
Bed seat: should be your bed’s length
and width plus 1.5 mm.
Bed hole axis Z and
pin axis Z: must be equal. A WARNING here means
the hinge pins won’t line up with the bed’s holes.
Machine cavity: the clear space under
the bed, in plan.
Relief lines: one for each thickened
area, with its position and depth.
Base part: the size of each printed
half, with a WARNING if it won’t fit your printer
(printer_size).
When everything looks right, go on to the test parts. The first one
to print is the top slice of the base: drop the machine into it and
check the fit before printing anything else.
3.11 Measurement worksheet
Measurement
First
Second
Entered
Bed length (in)
Bed width (in)
Plate thickness (in)
Hinge hole inset, left (in)
Hinge hole inset, right (in)
Hinge hole spacing (in)
Hinge hole below bed top (in)
Hinge hole diameter (in)
Bed cushions, compressed (in)
Thickened area 1: edge, start, end, thickness
Thickened area 2
Thickened area 3
Thickened area 4
Lowest point under the bed, from bed top (mm)
Slide plate: center, width, travel, thickness
4 Configuring the model
This chapter is an outline, still to be written. It will
cover:
Opening the model and using OpenSCAD’s Customizer.
The Customizer’s groups run roughly in the order a new builder will
want them: what to render and the main options, the machine and the
printer; then what to build (extensions and boxes, lids, ruler and
logos, handholds, rods, turn button, the organizer inserts); then the
side compartment and its options; then the fine detail of the body,
joints and hinges, which matters only for non-standard parts; and last
the tools and the test parts’ own settings.
The settings that decide the fit (machine bed, reliefs, hinges) and
the ones that are a matter of taste (compartment, extensions,
rounding).
The part setting and the views it gives: assembly, all,
test parts, individual parts.
Reading the console: what each line means, and every WARNING with
what to do about it.
Choosing a side compartment, extensions, trenches and lid
hinges.
Organizer inserts: bobbin trays (corner bay), notion trays and the
spool tray (back or left bay, chosen with ot_bay), the
stack-height budget the console reports, and the *_assembly
views.
Note: starting a Custom machine from a profile. The
Customizer’s preset menu, at the top of its panel, has a preset for each
machine profile, named for it with “(as Custom)”
(Singer 99K (as Custom), say). It sets
machine = "Custom" and fills every Custom machine setting
with that profile’s values, so you can change what differs on your
casting and save the result as a preset of your own. The presets live in
scad/vsm_base.json, which OpenSCAD reads alongside the
model; presets you save go into the same file, and are kept when it is
rebuilt. If git pull stops because that file has changes of
yours, run git stash, git pull,
git stash pop. To override just the printed hinge’s pin,
you don’t need Custom: set ph_pin_d and
ph_pin_engage.
Note: the barrel hinge.hinge_type = "barrel" takes the hinges from a vintage
portable case: a steel barrel, 15.2 mm across and 17.5 mm tall, standing
in a round hole, with an arm that pivots in the barrel’s slotted top on
a cross pin and a 6.85 mm pin that goes into the bed’s hole. A slotted
screw with a washer comes up from under the base into the barrel’s
tapped bottom; its head sits in a counterbore. The barrel is set so the
pin meets the bed’s hole: on the 99K its top stands 1.7 mm above the rim
(in its case it was flush with the wood, the bed sunk a little lower),
the back extension’s lip is notched round it, and the arm’s swing is cut
away in front of it. These hinges tip the machine back only about 65°.
Their dimensions (barrel_*, measured by Bob Drzyzgula from
a 99K’s case) may differ a little from hinge to hinge; print the hinge
coupon and try one first. The hinge needs only about 25 mm of back rim,
against the lollipop’s 42.
Note: a base without hinges.hinge_type = "none" makes a base for a machine to sit in,
for a machine without hinges or for anyone who doesn’t want them: no
hinge recesses or nut traps, no hinge checks or hardware in the console,
and no hinge test parts; the back-wall tunnels run the whole back wall,
and the hinge-hole measurements are ignored. The back rim starts at
back_rim_thin (12 mm) instead of the hinge’s 42 mm before
the base is rounded up to its depth class (below), so the 99K’s comes
out at 200 mm rather than 230; its back rim, and so its back extension’s
lip, differ from a hinged base’s. Nothing holds the machine in its seat,
so carry the machine and base separately, or strap them together; to
reach the cavity (an attached bay’s screws, say), lift the machine out.
Decide at print time: hinge recesses can’t be added well to a printed
base later.
Note: the printed hinge.hinge_type = "printed" is a hinge to print, for a machine
whose hinges are missing or broken, or which came in a molded base whose
hinges went with it (most portable Kenmores, for one). Each hinge is a
printed arm, a printed block and two
pieces of cut steel rod. The machine’s hinge holes run straight into the
back of the bed, so the machine can’t tip back on pins fixed in them;
like the lollipop hinge, which has a knuckle inside its round body, the
printed hinge’s arm turns. A steel pin, pressed into
the arm’s front face, goes into the bed’s hole; the arm turns on a steel
pivot rod that runs across the back, pressed into the
block’s two cheeks; and the block sits in a square recess in the back
rim. It is held by one screw driven up from under the base, its pan or
socket head in a round counterbore (ph_head_d), into a nut
slid into a slot in the block’s front face, below the arm, with plastic
under it for the nut to bear on. The pivot is set at the bed hole’s
height from your measurements, so the pin always lines up. The arm and
cheeks are cut down flush with the rim wherever that leaves
ph_min_cover (2.5 mm) of plastic over the rods: on the
Kenmore 158-14001, whose holes are 6.75 mm down, the whole hinge is
flush; on the 99K, whose holes are only 4 mm down, the arm stands 2.1 mm
proud, and the back extension’s lip is notched around it. The block and
the base’s recess are larger than the lollipop’s, so the back rim needs
about 8 mm more; the 99K still fits the 230 mm class.
The printed hinge, cut through the
middle: at rest, with the pin in the bed’s hole (left), and tilted back
to its stop (right).A printed hinge taken apart over its
recess in the back rim (part exploded): the block, the arm
above it, the pin drawn out of the arm’s front, and the pivot rod drawn
out to the side.
The arm runs on past the pivot into a short tail
(ph_tail, 12 mm). When the machine is tipped back, the tail
swings down into a pocket in the block and comes to rest on its floor,
so the machine stops at about ph_stop_angle (100°), where a
Singer lollipop hinge’s knuckle stops a 99K; nothing of the stop stands
above the arm. That is far enough to service the machine’s underside at
about 90°. On the way there the machine passes its balance point (about
55° on a 99K), where it takes the least effort to hold, and past about
75° the machine’s weight behind the base outweighs the base, so the base
starts to tip up unless you hold the machine or brace its arm (on a 99K
at 90°, about 6” above the table behind). The tilt prop (part
tilt_prop, one of the tools) does the bracing: a stand on
the table behind the base whose cradle, lined with felt, catches the arm
at 90°, so you can work with both hands while the machine’s weight goes
into the table instead of tipping the base. Its height and the cradle’s
radius come from the machine profile (6” and 1” for the 99K;
custom_tilt_prop_mm, or tilt_prop_h and
tilt_prop_r, for others): tip the machine back to 90° on a
level gauge and measure from the table to the underside of the arm. For
a machine whose arm isn’t round, a cradle radius of 0 in the profile, or
tilt_prop_top = "flat", gives a flat, level top instead. A
standalone version, with no machine settings but a sloping top and a
foot sized for stability, is in standalone/tilt-prop/.
Because the base tips first, the stop never has to hold more than a few
newton-metres, well within the pins and the plastic; don’t drop the
machine onto it all the same. Set ph_stop_angle between 45°
and 110°, or 0 for no stop. Check that nothing on your machine reaches
the base’s back rim before the stop. Print the hinges in PETG or another
tough filament; their rods are cut-to-length steel rod or dowel pins.
The pin’s diameter and how far it goes into the hole come from the
machine profile (1/4” and 12 mm for the 99K, 6 mm and 16 mm for the
Kenmore 158-14001), unless you set ph_pin_d and
ph_pin_engage; the pivot is ph_pivot_d (1/4”).
Hardened dowel pins make good rods and save cutting: set
ph_pin_len to a stock pin’s length, and the pin goes into
the bed’s hole by whatever is left past the arm; the console gives the
range of lengths that fit, from 8 mm into the hole up to just short of
its depth (hinge_hole_depth_mm in the profile: 22 mm on
both the 99K and the Kenmore, so their pins may be 30.5–43 mm long; a 6
× 40 mm pin goes 17.5 mm in, a 9/32” × 1 1/2” pin about 15 mm). Set
ph_pivot_len to a stock pivot’s length (1 1/8”, 28.575 mm,
say) and the block’s cheeks widen or narrow to suit. Precision dowel
pins are made a few hundredths of a millimetre over size (an m6 6 mm pin
is 6.004–6.012 mm), so try one in the bed’s hole before buying a set.
The console’s Printed hinge lines give the sizes, the rod
lengths, and where the parts stand against the rim. The printed hinge is
new in v34 (its tail stop in v35) and hasn’t been printed yet.
Note: a bed set flush, or standing on its feet. Some
machines sit with the bed’s top level with the base’s rim: the Kenmores
of the 1960s, whose bobbin covers lift on hinges rather than sliding out
over the edge, sat that way in their molded bases. A profile with
bed_flush sets the seat as deep as the plate (plus its
cushions). Some of those machines also stand on cast feet under the
casting, and their bases carried them on the feet; a profile with
foot_height_mm sets the floor from the feet (the plate’s
underside to the feet’s bottoms, plus bed_cushion_in for
pads under them), and the ledge round the cavity then sits 1 mm under
the plate and only locates the bed. inner_depth isn’t used
then. For a Custom machine these are custom_bed_flush and
custom_foot_height_mm.
Note: recessed lips and trim strips. The extensions
hold on with lips that lie on the base’s rim, and a lip is only as thick
as the bed stands above the rim: 5.3 mm on the 99K, nothing at all on a
flush bed. Where the bed stands less than lip_min_t (5.4
mm) above the rim, the rim is cut down under each lip so the lip keeps
that thickness and its top stays level with the bed: the left rim, and
the back rim along the back lip’s length, with a full-height island left
round each hinge, which the lip goes round. With the extensions off,
trim strips (parts back_trim and left_trim)
drop into the cuts and fill them back to the rim, held by the same peg
inserts in the same holes; they print flat, without supports. The cuts
are made only for the extensions you have turned on, and none at all
with ext_peg_holes = false, for a base that will never have
extensions. On the 99K nothing changes.
Note: a cord slot. Where a machine’s cords leave the
casting at the back (the Kenmore 158-14001’s foot-control connector, 50
mm from the right end), the profile’s cord_slot cuts a slot
through the back rim from the top down to the cords’ height. Unplug the
connector, lay the cords into the slot, and plug it back in; then press
part cord_slot_trim into the top of the slot, which leaves
a channel for the cords underneath. When the machine tips back, the
connector swings forward inside the base and draws the cords in through
the channel, so leave a little slack inside. The console warns if the
slot falls behind the back extension.
Note: an attached bay. A bed much over 12” is too
long to print as two halves with the side compartment built in. With
compartment_mount = "attached" the compartment becomes its
own part, right_bay, screwed to the base’s right end. Four
M5 socket-head screws go through the base’s end wall from inside the
machine cavity (tip the machine back on its hinges to reach them) into
heat-set inserts in the bay’s inner wall, and two 3/16” dowels locate
it, so its top sits flush with the base’s. The bay has its own handhold
and harness rods at its outer end, so the machine carries with the bay
on; the base keeps its own right handhold, rods and right-rim peg holes
for when it is off. The bay’s lid defaults to none
(attached_lid_type), since cords from the machine may lie
over its edge; hinged and lift-out lids are offered too. For now the
attached bay is storage only; the outlet and the knee controller are to
follow. Print attach_test first to try the inserts, dowels
and screws. The console’s Attached bay lines give the sizes and
the joint’s positions, and warn if a screw would run into a casting
relief.
An attached bay, pulled clear of the base
(part exploded, with
compartment_mount = "attached").
Note: an outlet base used for storage first. Set
compartment_option = "outlet" and
passthrough_knockouts = true: the base gets the outlet’s
curbs and screw hole, but the cord pass-through is closed at both ends
by thin walls, so the compartment works for storage. Cover the outside
screw hole with the printed cap. For a storage lid, switch
compartment_option to storage just to print
the lid; it is the same size. When you fit the outlet, tap the two walls
out with a punch and a small hammer, and print the outlet lid. To close
the pass-through again later, print passthrough_cover.
Note: a controller bay.compartment_option = "controller" makes the side
compartment a bay for a motor controller’s boards (the MCU controller,
or the analog one in the design study), with no knee mechanism. The two
gabled tunnels in the back wall behind the bay run on back to leave a 5
mm skin (ctrl_back_skin): one takes a fused IEC C14 inlet
standing upright, the other a panel of jacks for a low-voltage pedal.
Each skin is thinned to its panel’s thickness only round its cutouts. By
default the inlet takes the tunnel beside the divider, near the cord
pass-through, so the mains stays on that side
(ctrl_iec_tunnel). The jacks are keystone cutouts (keystone
inserts are sold with 3.5 mm and 1/4” jacks) or round holes for
panel-mount jacks (ctrl_jack_kind), in an array of
ctrl_jacks rows and columns.
The floor carries a sparse grid of posts for the boards, on a 1”
pitch by default so that a perfboard can be drilled to fit:
ctrl_grid sets the rows and columns,
ctrl_grid_pitch and ctrl_grid_offset their
spacing and place. For a commercial board, give its mounting holes as a
list (ctrl_post_list, placed by
ctrl_list_origin), and set ctrl_posts to
list, or to both to keep the grid too. Each
post takes an M3 heat-set insert or a thread-forming screw for plastics
(ctrl_post_hole). The pass-through to the machine cavity is
closed by knock-out walls until the motor’s leads need it
(ctrl_knockouts). The wiring inside is left to the
builder.
For a base already printed, part ctrl_mezzanine is a
plate that screws down onto the floor’s posts and carries a new set of
posts on top (mezz_posts, a grid or a list, in the same
frame as the floor’s), for a board that doesn’t fit the grid. With
mezz_lift, spacers come with it to raise the plate over
whatever stays below. The console lists the posts’ positions, and warns
if a post falls off the floor, a new post sits over a screw head below,
or the inlet and the jacks don’t fit their tunnels. Print
ctrl_panel_test first to try the inlet and the jacks.
The controller bay from above: the posts
on the floor, the pass-through closed by its knock-out wall on the left,
and the two tunnels in the back wall.
If back_ext_length is too short to reach the last back peg
hole, the back lip runs on past the body over the base’s back rim to
reach it (back_lip_extend), with a rounded end and a fillet
into the body; the console says how far. That extension then fits only a
base with the same back_peg_xs. If you move the base’s peg
holes left with back_peg_xs instead, the lip needn’t run
on, but the extension, again, fits only bases with those holes.
Note: standard sizes. So that bases share
extensions, and every extension takes the same inserts, sizes come in
standards.
Depth classes. The base’s front-to-back size is
200, 230 or 250 mm (base_depth; Auto takes the smallest
that fits), the spare going into the back rim. The 99K comes out at 200
with no hinges and 230 with lollipop or printed hinges; the Kenmore
158-14001 at 230 with no hinges and 250 with hinges. A class too small
for the machine stops the render; back_rim_width overrides
the class, with a note.
Height. Every extension’s top stands at
ext_height (88.225 mm, the 99K’s bed top), with the same
81.2 mm bays. A bed lower than that raises the base by thickening its
floor (the Kenmore’s by 3.9 mm, which makes its plate screws 5/8”); a
bed higher than that stands each extension on a podium (parts
back_podium, left_podium,
corner_podium), a frame at least podium_min (5
mm) thick, pinned to the extension by four 3/16” × 3/8” dowel pins.
ext_standard = false lets the extensions follow the bed
instead.
Length and pegs. The back extension is 240 mm long
(back_ext_length; other lengths get a note), and its pegs
sit at 16 and 160 mm from the base’s left face
(back_peg_xs), clear of the hinges and the split on both
machines.
Bases of the same machine and class share extensions. Machines whose
beds are set flush, like the Kenmore, won’t share extensions with
machines whose beds stand on the rim, like the 99K, since the lips sit
differently; nor will a hingeless thin-backed base share a back
extension with a hinged one, and other differences (a printed hinge’s
notch in the back lip, say) can break the match too.
Note: larger extensions and their bins. The left
extension’s width (left_ext_width) and the back extension’s
depth (back_ext_depth) are 100 mm at least; 100 mm more on
the left makes a table about the size of a Sew Steady Junior. Each piece
keeps the bay a 100 mm piece gives, against the base, so the inserts
always fit it: the bobbin bin in the corner, the notion and spool trays’
bays in the left and back extensions. Whatever a piece has past that
becomes open bins, each behind a divider (ext_divider, 2.5
mm) whose top is level with the lid’s ledge, so it helps hold up the one
lid; a finger notch in the middle of each divider
(ext_divider_notch, 30 mm wide and 20 mm deep) lets you
reach into a narrow bin, and keeps papers in it from flopping over. In
the corner, the bins go left of the bobbin bin and behind it; with both
larger, corner_layout decides the rest: 2x2
gives the far corner a bin of its own, long left runs the
left bin the full depth, and long back runs the back bin
the full width. The left and back extensions get one outer bin along
their length (1+1), or two (1+2,
left_ext_layout, back_ext_layout); their inner
bay stays whole. A strip under ext_bin_min (10 mm) inside
is left solid.
Two equal bins.left_ext_double and
back_ext_double work out the width or depth for an outer
bin the same size as the inner one, ignoring left_ext_width
or back_ext_depth, and the console gives the size used. The
corner and the extension beside it share that size, and their bays can
differ by a little (each lid’s hinge edge sets its own ledge), so the
larger need wins and the other piece’s outer bin is walled in to match
its inner one. With both on, a 2x2 corner holds four bobbin
stacks, and a 1+1 left extension two spool or notion
trays.
One lid or a lid per bay. Each piece takes one lid
over all its bays (back_lids, left_lids,
corner_lids = one), resting on the dividers
too, or a lid per bay (per bay), each in its own rabbet.
Per bay, the bays are spaced for a ledge either side of an
ext_frame rib between the rabbets, about 12 mm, and under
the ledges the divider tapers at 45° to ext_divider at the
floor, so it prints without supports and takes little plastic; there are
no finger notches. The inner bay’s lid keeps its piece’s lid settings;
the outer bins’ lids share bin_lid_type (lift-out by
default) and bin_lid_hinge, with a finger hole sized to the
lid. A bin under bin_lid_min (15 mm) inside gets no lid,
and a hinged bin lid too small to hinge (under 30 mm along the hinge or
20 mm across) is made lift-out, with a warning. The bin lids print as
part bin_lids, and go on the all plates with
the others. A per-bay inner lid with bins beside it uses a finger hole,
not a tab, since a tab’s notch would cross the bins.
Larger extensions with
left_ext_double and back_ext_double, one lid
each (lids off): a 2x2 corner with four bobbin-bin-sized bins, the left
extension split 1+2, and the finger-notched
dividers.The same sizes with a lid per bay, lids
lifted: each bay in its own rabbet, the bin lids lift-out with finger
holes, the inner bays’ lids hinged as before.
Note: a ruler and logos on the front face. Many
machines have a ruler on the front of the bed, handy for a quick length
check; the idea of putting one on the base is Danielle’s.
ruler = true puts one across the base’s front face, and
across a built-in compartment’s, but not on an attached bay or the
extensions.
Its extent. It runs the whole flat face, from where
one corner’s round-over ends to where the other’s begins. The harness
rods enter the front face near each end, so a ruler low enough to meet
their holes stops just clear of them instead, about 10 mm in from each
end. The console says so, and gives the ruler_bottom (12
mm) that runs it out to the round-overs.
Its scales. One to three, stacked from the bottom
up (ruler_scale_1 to _3): inch,
cm, custom or none. The default
is inches below centimeters, starting 5 mm up
(ruler_bottom), 8 mm per scale
(ruler_scale_h).
Its ticks. Each scale has its own divisions per
unit and a longer tick every so many: ruler_inch_div and
ruler_inch_mid (8 and 2, eighths with the quarters longer;
10 and 5 gives tenths with the half longer), ruler_cm_div
and ruler_cm_mid (10 and 5). A custom scale
takes its unit in millimeters, its divisions, its longer tick and a name
(ruler_custom_*).
Its numbers. Each unit is numbered over its long
tick (ruler_number_every thins them), and the scale’s name
stands over its first half unit.
Line widths. Every line is at least
ruler_line_w (0.6 mm) wide, and the lettering is thickened
to match, since a slicer drops lines much finer than its nozzle.
logo_left and logo_right take an SVG file
each (a path relative to the model’s folder, scad/, or a
full path), placed in the face’s upper corners, logo_inset
(6 mm) in from the flat’s ends and down from the top’s round-over. Each
is stretched to logo_size (25 × 15 mm), so set that to the
logo’s own proportions. An SVG must be clean outlines: text converted to
paths, and overlapping shapes merged. OpenSCAD ignores fill and stroke,
so an invisible shape, such as an unfilled rectangle left from a text
frame or an artboard, imports as a solid block that buries the logo;
delete it (in Illustrator, Object > Path > Clean Up, with
Unpainted Objects ticked). A path that crosses itself makes OpenSCAD
2021.01 drop the whole relief, ruler and all, with “The given mesh is
not closed”.
face_relief makes all of them raised (the
default), engraved, or inlaid (engraved and
filled flush with a separate part), by face_relief_depth
(0.6 mm). With face_relief_chamfer (on by default), a
raised mark stands on a 45-degree slope under each of its
downward-facing edges, and an engraved recess has one over each
upward-facing edge; square, those edges print as a flat overhang that
curls and roughens the mark. Inlaid marks are filled, so they keep
square walls. Raised and inlaid marks are color-tagged for another
filament, as on the standalone bobbin box: the base, the ruler and each
logo get their own random color, spaced evenly round the color wheel,
with the ruler opposite the base for the strongest contrast.
face_color_seed picks another set, and the console lists
them. Export the base part as 3MF, not STL, to keep the
tags, from an OpenSCAD with the Manifold backend: Bambu Studio and Orca
open it as a multi-color part and ask which filament each color gets. An
STL merges everything, so inlaid marks disappear into a plain face. The
base prints standing on its bottom, so the marks are on a vertical face
and need no support, but every layer they run through changes filament:
about 16 mm of the base’s height for a two-scale ruler, and the logos’
height again. On a single-nozzle printer each change costs a purge and
time; a printer with several toolheads makes it practical. With
split set, each mark is split with the base.
Maker’s marks on the back and bottom. Four more SVG
places suit a maker’s name, a model and serial number, or a build date.
Prepare each as an SVG, with text converted to outlines.
back_logo_left and back_logo_right sit
near the back face’s lower corners, as you look at the back, so the left
one is at the base’s right end. Each is stretched to
back_logo_size (40 × 15 mm) and set
back_logo_inset (6 mm) in from the face’s flat end and up
from the bottom. The flat end is measured from the harness rods’ holes,
which come through the back near each lower corner, so the logos clear
them. They follow face_relief. The back extension sits
against the back face and hides them, and the console says so.
bottom_logo_left and bottom_logo_right are
centered on the two halves of the base, where it splits, in the same
places whether or not split is set. Each is stretched to
bottom_logo_size (80 × 40 mm). They read with the base
tipped back onto its back edge, front edge up. The base prints standing
on its bottom, so these can’t be raised: bottom_relief
makes them engraved (the default) or inlaid.
An inlay on the bottom is the cheap kind of second color, because it
lies in the first few layers, so only those layers change filament. The
console warns if one reaches a handhold at the end or the split’s
mending plates.
With all seven places used there are eight color tags: the base, the
ruler, and the six logos.
A ruler on the front face, inches below
centimeters, inlaid, with a logo in each upper corner. The harness rods’
holes, near each end, are the reason it stops short of the round-overs
there.
The five bobbin trays stacked on their
center post, lifted out of the corner bay (part
bobbin_trays, printed in PETG), with metal and plastic
class 15/66 bobbins.
A standalone bobbin box. The corner bay and its
bobbin trays also come as a separate, self-contained model,
standalone/bobbin-box/bobbin_box.scad: a small lidded box
with the five-tray stack, which needs nothing from the main model. It is
a way to try a small piece of the project, or to give someone the box
without the base. It has its own settings (trays, lid type, bobbin size,
hinge and lid fit, and an SVG image on any of its six faces, raised,
engraved or inlaid in a second color) and test parts; see its
README.
5 Test parts
This chapter is an outline, still to be written. It will
cover:
Why print tests, and the order to print them in.
Test parts and tools: test_parts gives pieces of the
base for trying fits, and each piece is also a part of its own, named
below, so any one can be printed by itself; tools gives the
things printed to help build or measure, which aren’t part of the base:
the hinge nut tool (hinge_nut_tool), the printed hinge’s
rod-fit test (printed_hinge_test), and the two halves of
the foot-locating rig (foot_rig_left,
foot_rig_right), and the tilt prop
(tilt_prop). Each tool is also a part of its own.
Top slice of the base (top_test): does the bed drop in
and sit flat, and do the hinge pins line up?
Bottom slice (bottom_test): the floor, a little way up
into the cavity.
Dovetail coupon (dovetail_test): joint clearance
(split_clearance, key_flare_angle) and the
plate-pocket bridge.
Center slice (center_test): all three dovetails with
the plates installed, the front seam, and clearance under the
machine.
Left-end strip (end_strip_test): handhold feel,
knock-out wall, rod fit (rod_hole_d).
Hinge block (hinge_block_test): hinge fit and bolt
length.
Hinge coupon (also part = "hinge_coupon"): a quick
check of the hinge recess and pin slot without printing a slice of the
base.
Center slice: the front-wall serrations, and which half goes on
first (lower the right half onto the left).
Rod plugs (rod_plugs): press fit in the end strip’s rod
holes.
Lid hinge test (lid_hinge_test, in the test set since
version 81): a small lid in its frame, with the lids’ snap-in
hinge.
Compartment test (its own part,
part = "compartment_test", built-in compartment only): the
base’s whole right end, from just left of the divider, so both ends of
the cord pass-through and their knock-out walls are included, to the
right end wall with its handhold and harness rods. It prints as the base
does, and is the way to build and try the outlet (or any other)
compartment by itself.
Printed-hinge rod fit (its own part,
part = "printed_hinge_test"): a bar with five vertical
holes for the pin, printed as the arm prints them, and five horizontal
teardrop holes for the pivot rod, printed as the block prints them, from
− 0.2 mm to + 0.2 mm left to right around their own settings (one to
five notches on the top edge mark them): ph_pin_press for
the pin holes, ph_press for the pivot holes. At the loose
end, under a plus on the top, is a sixth hole, horizontal only: the
arm’s running fit for the pivot rod, ph_slip. Press the pin
into each vertical hole and the rod into each horizontal one, and set
each setting to the step that holds firmly without splitting the
plastic; the two often differ, since vertical and horizontal holes print
differently. The rod should turn freely in the sixth. To home in, print
a second bar with the settings at their best steps and a finer
ph_test_step (0.05 mm, say).
Controller panel test (ctrl_panel_test, controller bay
only; in the test set): the outer part of the back wall behind the
controller bay, with the IEC inlet’s and the jacks’ cutouts in their
thinned panels and a short length of each tunnel, printed face down, to
try the inlet and the jack modules before printing the base.
Cordset entry test (knee_entry_test, knee controller
only; in the test set): the 4.4 mm wall with the cordset’s entry hole,
the dimple for its clip and the clip’s guides, to try the cordset’s
molded entry and steel clip.
Attached-bay joint test (attach_test, attached bay
only; in the test set): the base’s end wall and the bay’s inner wall
around one screw and one dowel, each printed upright as in its part. Fit
an M5 heat-set insert, press in a dowel, and try the screw and the fit
of the two faces.
Split test (its own part, part = "split_test", not in
the test set): just the front of the split joint, both halves, with the
front-wall serrations and the first dovetail key, for a quick check of a
serrated joint. The wall stubs are split_test_h tall (30
mm; 0 for full height).
Pass-through (passthrough_test, outlet, knee or
controller compartment): the divider around the cord tunnel, cut down
its middle into two pieces, each with one of the two knock-out walls, as
the base has one on each face of the divider. Try knocking each out.
(Before version 81 it was one piece, with the tunnel sealed inside it
between the walls; a slicer that split it into its shells filled the
tunnel solid.)
Turn button (turn_button_test, with
turn_button on): a slice of the front rim with the button’s
pad and nut slot, and the button.
Outlet block (outlet_test, outlet compartment only):
curbs, screw height, and the insert or through-screw hole, with your
outlet and plugs in place.
Extension top slices (ext_top_test): lip fit, pegs,
supports, and the bobbin-plate trench.
Lids (each its own part: base_lid,
back_lid and so on): snap-in hinge, swing, and the
lean-back stop.
Front corners (front_corner_test): the base’s front
left and right corners, full height and a little deeper than the front
wall, each printed upright as in the base, for trying the logos and the
ruler: relief depth, line widths, and, raised or inlaid, the filament
changes and colors. Each is wide enough for a 40 mm logo, or the logo if
wider, with the ruler below it; test_corner_w sets the
width instead.
Ruler and logos: every piece cut from the base carries the raised or
inlaid ruler and logos it crosses (the center slice, the top and bottom
slices, the corners), each as its own color-tagged part, so export 3MF
to keep the colors. (Before version 75 the test pieces left them
off.)
Note: the hinge coupon as a wooden-base insert. The
hinge coupon has countersunk corner holes for #8 flat-head wood screws,
so it can also be used in a base made of wood. Print two, mortise them
flush into the top of the base with their front edges on the back wall
of the bed opening, at the hinge spacing the console gives, and screw
them down. The console also gives how far below the bed’s top surface
the coupon’s top must sit, and where the hinge-pin axis falls. The
router work for the hinge recesses, the hardest part of a wooden base,
is then done by the printer.
In the part list, the test parts come last, together;
before them come the views, the base and its small parts, the extensions
and boxes, the printed hinges, the knee controller, the controller bay,
the bobbin and notion trays, and the tools. The compartment test (the
base’s whole right end) and the split test (which the center slice
covers) stay out of the test set; print them by name.
6 Printing
This chapter is an outline, still to be written. It will
cover:
Slicer settings that matter: walls, infill, bridging, and
brims.
The base halves: orientation and what to expect. The split sits left
of the middle by half the dovetail keys’ depth
(split_balance), so the two halves, the left one’s keys
included, are the same length. Even so, the Kenmore’s halves (231.5 ×
250 mm) only just fit a 256 mm bed: in Bambu Studio, rotate each until
the keys clear the excluded corner.
Extensions: printed upright with supports under the lips.
Print plates: part = "all" gives every part of the
build in print orientation, grouped into plates for your
printer_size and printer_margin;
print_plate = N gives plate N on its own. The console lists
the plates and which need supports.
Lids: printed top face down. Print lid_hinge_test first
to check the snap-in hinge in your filament.
Extension pegs (part = "ext_pegs"): printed lying down,
never standing up; print a few spares.
Printed hinges (part = "printed_hinges", in PETG): two
blocks printed upright and two arms standing on their front faces, so
the pin’s hole is vertical and the pin’s load lies along the layers; no
supports. The pivot holes are teardrops with their points up.
Trim strips (back_trim, left_trim) print
flat on their undersides, cord_slot_trim upright, and the
outlet’s wall-slot trims (outlet_trims) lying on their
sides, all without supports.
Features removed after printing: knock-out walls under the
handholds, sacrificial membranes over screw holes.
Note: lid hinges in PLA and PETG. The hinge defaults
(lid_tab_w = 4, lid_bump_engage = 1.0) come
from test prints in both PLA and PETG. With the narrower 2.5 mm flex
tabs of earlier versions, a PLA lid popped out of its hinge almost every
time it was opened: PLA is stiffer than PETG and the narrow tab bowed
away instead of holding the bump in. If a lid still comes out too
easily, tighten lid_hinge_end_clearance or make the bumps
steeper with a smaller lid_bump_angle; if it is hard to
snap in, do the opposite. Try changes on lid_hinge_test,
which prints in a few minutes, before printing a full lid.
The same hinge, at the current defaults, was tested again in November
2026: lids printed in PLA and in PETG, each fitted to boxes printed in
PLA and in PETG, held securely in all four combinations. The test lids
were printed at 0.12 mm layers and the boxes at 0.20 mm. Fine layers
give the lid’s cone-shaped bumps a smoother, truer flank, and the lid
prints quickly enough that they cost little; the base and boxes print
fine at 0.20 mm, where finer layers would take far longer.
Note: infill near the hinges. The base has been
printed at 15% infill without trouble, and that is enough at the hinges
too: around the screw holes, the hinge recesses and the nut traps, the
load is carried by the walls the slicer lays round every hole and face,
not by the infill. What matters is enough of them: use 4 wall loops
rather than 2, and 5 or more top and bottom shell layers, so the recess
floors and the traps’ roofs are solid skins. For more margin, add a
modifier in the slicer over each hinge (in Bambu Studio, right-click the
part, Add modifier → Box, and move it over the recess and the
trap below), with 40–50% infill and 5 or 6 walls; the halves print
separately, so it is one box per hinge. The printed hinge’s arm and
block are better printed denser throughout.
Note: supports under the lips and trenches. The
extension lips and the bobbin-plate trenches in the lids need supports.
Standard (not tree) supports, with a separate support material printed
on the interface layer, give a clean underside: the trench floor below
was printed over them, in a lid printed top face down so the top takes
the bed’s texture. On a printer with a second material, the slicer adds
a purge tower to each plate with supports; leave room for it.
The floor of a bobbin-plate trench,
printed over standard supports with support material on the
interface
Note: one supported layer per part. Where a part
needs supports, the model keeps its supported surfaces on a single
layer, so a printer without an automatic material changer needs only two
filament changes for the support material: one before the interface
layer and one after. The lid with a bobbin trench and the extension lips
each have one such layer. (The old molded extension pegs added a second,
which is one reason the separate pegs are better.) Two supported parts
share a plate only when their interfaces are on the same layer, and the
plate keeps a corner clear for a purge tower
(purge_tower_size). The console warns about any part with
supports on more than one layer.
7 Assembly
This chapter is an outline, still to be written. It will
cover:
Clearing the membranes and knock-out walls.
Nuts into the plate and hinge nut traps.
Joining the halves: dovetails, then the mending plates from
below.
Tip: once the nuts are in their traps in the cavity floor, put a
strip of masking tape over them. Then they stay put when you turn the
base over to drive the plate screws in from below; peel the tape off
afterward.
The joined halves from below: three
mending plates across the split, each with four 1/2” #8-32 flat-head
screws.Inside, the screws’ nylon-insert locknuts
sit in their traps in the cavity floor, either side of the dovetail
keys. The screws push through the traps’ printed membranes; no drilling
needed.
Installing the hinges and setting the machine on its pins.
The hinge nuts (lollipop hinges): the nut traps open on the
underside. Push a nut onto the tip of the printed nut tool
(part = "hinge_nut_tool"), nylon side first for a locknut,
slide it up the trap until it seats, and hold it there while you start
the screw from above; once the screw has caught, pull the tool out and
finish. The tip is sized for the 1/8” bore of a nylon-insert locknut
(hinge_nut_tool_tip). A standalone version for other nut
sizes and trap depths is in standalone/nut-tool/.
Printed hinges: cut the pins and pivots to the console’s lengths and
deburr them. Press a pin into each arm’s front face to the bottom of its
hole (a vise works). Slide a nut into the slot in each block’s front
face, under the arm’s channel, until it lines up with the screw hole.
Set the arm between the block’s cheeks and press the pivot rod through
cheek, arm and cheek until its ends are flush with the block’s sides,
with the arm’s engraved arrow on its bottom face, pointing toward the
pin (the arm isn’t symmetrical top to bottom); the arm should swing
freely. Drop the block into its recess, pin toward the bed; the recess’s
front wall closes the nut’s slot. Drive the screw (#8-32 × 5/8”, pan or
socket head) up from under the base, through the round counterbore (its
head bears on the counterbore’s roof; push it through the printed
membrane), into the block’s nut. The recess walls keep the pivot rod
from working out.
Trim strips, with the extensions off: tap the peg inserts into the
trims’ holes, as into the lips, and press the trims into the rim cuts.
The cord slot’s trim presses into the top of the slot once the cords are
in.
Outlet cords through the walls: with the outlet in place, lay each
cord down into its wall slot (with rear, press the
controller cord on edge into the floor channel first, past its lips,
starting at the bend), then press the trims in from above.
Harness rods and carrying.
An attached bay: inserts into its inner wall, dowels into the base’s
end face, then the four screws from inside the machine cavity.
Extensions on their pegs, the corner piece’s dovetails, and snapping
in the lids.
8 Other machines and hinges
This chapter is an outline, still to be written. It will
cover:
The profiles so far: the Singer 99K, and the Kenmore 158-14001 (a
425 × 185 mm bed set flush and carried on its three feet, 6 mm hinge
holes, a cord slot at the back), measured by Bob Drzyzgula. The
Kenmore’s bed is too long for halves with the side compartment built in:
use compartment_mount = "attached", and
hinge_type = "printed", since its own hinges went with its
molded base. Its base is in the 250 mm depth class with the printed
hinge, so lower printer_margin to 3 mm to fit a 256 mm
printer, or set back_rim_width (outside the standard
classes). Its bed sits 3.9 mm lower than the 99K’s, so the base is
raised to the standard extension height.
What changes between machines, and what to measure.
Machines without a side compartment, and bases for larger beds.
Adding a hinge type: the footprint functions and the cutter
module.
Contributing a machine profile.
9 Knee controller
This chapter is a draft. The mechanism has been checked in the
model but not yet built. The feel (force and travel) follows a Singer
knee controller as measured; the pot’s gearing is a placeholder until
the board’s speed against resistance has been measured.
With compartment_option = "knee", the base’s right bay
becomes a knee speed control, in the manner of Singer’s own knee-lever
machines. A bar hangs down past the table edge. Pressing it with your
knee turns a shaft running front to back in the bay. Gears on the shaft
turn a potentiometer, which takes the place of the slide pot on an
inexpensive foot-pedal speed-control board. A snap switch keeps the
motor off for the first inch of travel.
The knee controller in the right bay
(part knee_assembly, a cutaway): the spring housing and the
hub’s crank on the front face, the shaft, the gears in front of the
bulkhead, and the board cover at the back.
Warning: mains voltage. The donor board, the pot’s
pins, the switch’s terminals and every wire to them are live whenever
the controller is plugged in. The triac’s tab is connected to the live
side. Work on it only with the plug pulled, keep the printed cover on
the board, use wire rated for 300 V or more, and don’t use a pot with a
metal shaft (see below). If you are not comfortable building mains
equipment, don’t build this part.
9.1 The feel
The defaults follow a Singer knee controller, measured at the knee,
12.5” below the shaft (knee_bar_drop):
Knee travel
Force
What happens
0 (rest)
about 1 lb
The spring’s preload
0 to 1”
rising to about 2.5 lb
Dead travel: the switch holds the motor off
1” (knee_travel_on)
about 2.5 lb
The switch closes; the motor starts
1” to 2”
about 2.5 to 4 lb
The speed range
2” (knee_travel)
about 4 lb
Full speed
2.25” (knee_travel_max)
about 4.3 lb
Hard stop
The force rises in a straight line, about 1.5 lb per inch
(knee_force_rest, knee_force_rate). The
console’s Knee controller block gives the figures for your
settings, in pounds and newtons.
9.2 How it works
Bar and hub. The steel bar’s square end plugs into
the printed hub on the front face. The hub’s crank reaches sideways,
away from the push, into the spring housing beside it. The hub is fixed
to the 8 mm shaft with a set screw, but that screw only turns the shaft
for the gears: the knee’s force goes from the bar through the hub’s
crank into the spring and the stops, never into the shaft, its set
screws or the gears.
Spring and stops. The housing, screwed to the front
face, holds a compression spring standing upright. A steel pin across
the crank’s tip bears on a printed cap on top of the spring. At rest the
spring pushes the crank up against the rest screw in
the housing’s roof. At full travel the pin comes down onto the
stop screw, which stands up through the middle of the
spring from the housing’s floor. Both are M4 screws in captive nuts,
with jam nuts, so rest and full travel are adjustable and steel meets
steel at the hard stop. The housing is a closed loop: the spring’s
preload stays inside it, and only the knee’s push reaches the base,
through a tongue on the housing’s back that sits in a pocket in the
face.
Shaft. The shaft runs in two flanged bronze
bushings, one in the front wall and one in a bulkhead across the
bay.
Gears. Two stages, about 11.75:1 overall. A
64-tooth sector on the shaft drives a 16-tooth pinion on an idler, 4:1
(knee_ratio); a 47-tooth sector on the same idler drives a
16-tooth pinion on the pot’s own shaft, 2.94:1
(knee_gear2_teeth, knee_pinion2_teeth). The
idler turns on a 3/16” steel pin pressed into the bulkhead; the pot’s
bushing is its pinion’s bearing. The model generates each pinion by
rolling it against its gear, so the 16-tooth pinions have the undercut a
small pinion needs and each pair runs with a little backlash.
Switch. The switch lies on the bulkhead under the
shaft, lever up. A cam on the sector holds its lever down at rest, so
its normally-closed contact is open and the motor is off. A ramp on the
cam lets the lever up at 1” of knee travel. The switch is wired in
series with the motor.
For why this controller behaves as it does (an open-loop triac phase
control, like a good stock pedal, that holds no speed under load), and
for the microcontroller design that follows it, see the companion paper,
Speed Control of Universal Motors in Sewing Machines (docs/motor-control/).
The console’s Knee controller block gives the numbers for
your settings: the shaft’s angles, the gearing, how far the pot turns
and how much of its resistance that spans, where the switch releases,
the spring’s load, the knee force along the travel, and warnings if
anything runs into the bay’s walls, the floor, the bulkhead or the ends
of the front face.
9.3 What you need
The hardware list in the console has the full list, with lengths.
Item
Part
Notes
Speed-control board
XWW KB3151C “speed controller” pedal board, 75 × 35 mm
BT136-600E triac, DB3 diac, two 0.1 µF X2 capacitors, 2 MΩ min-speed
trimmer (VR2); 110–120 V, 1.0 A
Pot
Bourns 91A1A-B28-A25L
1 MΩ linear cermet; plastic slotted 1/4” shaft, 7/8” long; 3/8-32
bushing with nut and lockwasher; anti-rotation lug
Off switch
Omron SS-5GL (Digi-Key)
Hinge lever, SPDT, 5 A at 125 VAC; the standard 0.49 N version, not
the low-force SS-5GL-F
Shaft
8 mm steel rod, about 77 mm
File two small flats for the set screws
Bushings
2 × flanged bronze sleeve bearing, 8 × 12 × 10 mm, flange 16 × 2
mm
Pressed into the front wall and the bulkhead
Pins
rod_d rod (3/16”): 24 mm for the idler, 14 mm for the
crank
The same rod as the harness rods; a 3/16” push-on retaining nut for
the idler
1 × M4 × 35 (stop), 1 × M4 × 14 (rest), each with 2 nuts
One nut of each is captive in the housing, the other a jam nut
Bar
Steel, 3/8” square at the hub end
Out from the hub, bent down 12.5” (knee_bar_drop)
Screws
M3 set screws, M3 screws and nuts, M3 heat-set inserts; 2 M2 × 12 or
#2-56 × 1/2” for the switch
2 × M3 × 12 hold the spring housing
Power, cordset
A standard pedal controller cordset
Its molded entry and steel clip fit the base’s entry
Power, iec
Qualtek 723W-X2/03 fused C14 inlet (snap-in, 1.5 mm panel; or
Schurter 6200.4315), its fuse drawer, a T2A 5 × 20 mm fuse, 4.8 mm
(0.187”) female quick-disconnects for its tabs (6.3 mm for the
Schurter); 3 Wago 221-413 lever connectors
Earth strip (brass or phosphor bronze) for the shaft
Print the knee parts (knee_sector,
knee_idler, knee_pinion,
knee_hub, knee_spring_housing,
knee_spring_cap, knee_cover, and
knee_cord_clamp for a bare cord) in PETG. They are on the
print plates with the other small parts. The hub prints back face down,
with the crank flat on the bed, so the crank’s bending runs along the
layers. The spring housing prints standing on its floor. Print
knee_entry_test first if you are using a cordset.
9.4 The pot
The board’s original slide pot (VR1) comes off, and the Bourns pot
takes its place as a two-terminal variable resistor. In the board’s own
terms:
the Bourns pot’s wiper goes to the old
pin-2 pad;
the pot’s end that the wiper approaches at full knee
travel goes to the old pin-1 pad;
a jumper joins the old pin-3 pad to the pin-2 pad,
which puts RV2 across the pot.
Over the speed range, from 1” to 2” of knee travel, it should sweep
about the same resistance as the slide pot did, about 220 kΩ
(knee_r_span). The shaft turns only 4.5° over that inch, so
the gearing is high: the pot turns about 53°, about 221 kΩ of its 1 MΩ.
This is a linear placeholder. The board’s speed is far from linear in
resistance (low speed is crowded into the high-resistance end), so the
gearing, or the gear shapes, will change once the board’s speed against
resistance has been measured.
From the Bourns datasheet [1]:
The 91 is a 5/8” (15.9 mm) square single-turn panel control with PC
pins in line. Mechanical rotation is 300°, electrical travel 240°
(linear).
Shaft code B28 is a plastic, single-slotted 1/4” shaft, 7/8”
long.
Bushing A is 3/8-32 UNEF, 3/8” long, with an anti-rotation lug at
0.305” (7.75 mm) radius. The L suffix fits the lug.
Cermet: 2 W at 70 °C, limited to 350 VAC. The dielectric
withstanding voltage is 1,500 VAC between the element and the bushing.
Rotational life is 100,000 cycles.
The plastic shaft matters. The bar, hub, shaft and gears are things
you touch. The pot’s plastic shaft and the printed pinion are what keep
them apart from mains, together with the pot’s 1,500 VAC rating between
element and bushing. Don’t substitute a pot with a metal
shaft.
The pot mounts from behind the bulkhead, with its bushing through the
3 mm panel and its nut on the front. The lug goes into the small hole
beside the main one; knee_pot_lug_angle sets where that
hole is, so you can turn the pot to put its pins where the wiring is
easiest.
Setting the pot. Set it at full speed. Hold the bar
at 2” of travel, turn the pot’s shaft until the wiper just reaches 0 Ω
to the pin-1 end, and tighten the pinion’s clamp screw. At rest it then
reads about 445 kΩ (the console gives the figure for your settings).
From full speed to the hard stop the pot turns another 13° into the dead
zone past its electrical end, where the resistance stays at 0; its
mechanical stop is about 30° beyond the electrical end, so the pot is
never the hard stop.
9.5 The switch
From the Omron SS datasheet [2]:
The body is 19.8 × 10.2 × 6.4 mm. Two mounting holes, 2.35 mm across
at 9.5 mm pitch, take M2.3 screws with washers. M2 or #2-56 screws
work.
The hinge lever is stainless steel, 0.3 mm thick.
The SS-5GL operates at 8.8 ± 0.8 mm from the mounting-hole line. Its
free position is 13.6 mm at most, and its overtravel at least 1.0 mm.
Operating force is 0.49 N at most.
It is rated 5 A at 125 VAC (resistive), with a mechanical life of 30
million operations and an electrical life of 200,000.
The lever’s actuating point is 14.5 mm from its pivot end, about 5.3
mm from its free end (knee_switch_act).
The switch screws to the front face of the bulkhead, lying under the
shaft, lever up and its free end toward the push, so that the actuating
point is straight below the shaft. Its two slots let it move ±1.5 mm up
and down. The cam on the sector has a dwell, a stretch at a constant
radius that holds the lever down at rest, then a ramp at about 45° that
lets it rise. The switch releases at 1” of travel
(knee_travel_on), about 4.6° of the shaft’s swing. Past the
ramp the cam still rests lightly on the lever, well above its release
point.
To adjust it: with the bar at rest, slide the switch up until it
clicks off, then a little further (knee_switch_press, 0.3
mm), and tighten the screws. Then set where it releases by turning the
sector on the shaft: loosen its set screw, hold the bar at 1” of travel,
turn the sector until a meter across the normally-closed contact just
shows it closing, and tighten the set screw. Turning the sector is the
fine adjustment (each degree moves the release point about 5.5 mm at the
knee); the switch’s height is coarse (each 0.1 mm moves it about 1.9
mm).
Wiring. Put the switch’s normally-closed contact in
series with the motor lead. Through the dead travel the motor is then
fully off, rather than creeping at the minimum speed set by the board’s
trimmer.
If the switch’s contacts were ever to weld, the motor would creep at
the rest setting rather than run away. Setting VR2 as low as the motor
will still start keeps that creep small.
9.6 The return spring
The spring is a compression spring standing in the housing: by
default McMaster’s 9001T46 [5], 0.6” (15.24 mm) outside diameter, 0.072”
(1.83 mm) wire, 1.25” (31.75 mm) long, 45 lb/in (7.88 N/mm), rated 26 lb
at 0.668” long (14.8 mm of deflection). Any spring of about that size
and rate will do; set knee_spring,
knee_spring_rate and knee_spring_max to its
figures.
The model sets the crank’s length from the spring’s rate so that the
knee feels knee_force_rate: with this spring, 58 mm
(knee_crank_r; set it to fix the length instead). The
spring is preloaded 3.1 mm at rest, 24 N, which gives the 1 lb at the
knee, and compressed 13.4 mm at the hard stop, 105 N, 90% of its rating.
The crank’s lever arm is what turns a 45 lb/in spring into 1.5 lb/in at
the knee: the knee is 5.5 times as far from the shaft as the crank
pin.
The housing stands beside the hub, on the side away from the push (to
the left of the hub for a knee that pushes right). The console warns if
the housing would run off the end of the front face, reach the base’s
bottom or top, or if the spring is compressed past its rating.
9.7 The board
The board lies flat in the back of the bay, its long axis front to
back, components up, on three posts 8 mm above the floor: a boss for an
M3 heat-set insert (the board’s 5.5 mm hole takes an M3 screw and
washer), a peg that fits the notch in the board’s end, and a plain rest
post. The positions are those of the board’s own enclosure:
the peg is 47.3 mm along and 5.0 mm across from the screw;
the rest post is 4.3 mm along and 19.5 mm across from the
screw.
Along is measured from the notched end, across from the long edge
nearer the screw; with the components up, across is to the right of
along. knee_board_screw is the screw’s position, 49.6 mm
along and 12.5 mm across, measured from the board. By default the board
is turned with its notched end toward the back of the bay
(knee_board_turn), which puts its two spade tabs on the
right, near the front, where the power leads come in. The cover leaves
16 mm beside them for the connectors and their wires
(knee_board_tab_room).
The printed cover goes over the board and screws down with two M3 ×
30 screws into inserts in floor bosses. Its notches let the leads out:
the front notch, by the divider, for the pot and switch leads and the
motor lead; the side notch, beside the spade tabs, for the power
leads.
Heat. The board is labeled 1.0 A. Its BT136 triac is
a 4 A part, but it has no heatsink, and at more than 1 A it runs hot in
a closed box. If your motor draws more (knee_motor_amps),
fit a small clip-on heatsink to the triac and the cover gets vent slots.
The triac’s tab is live, so the heatsink is too: keep it inside the
cover.
9.8 Power
knee_power chooses how the controller is wired in. All
three are at mains potential.
cordset (default). The controller takes
a standard pedal controller cordset, the kind that is sold separately
with a three-pin machine plug or a duplex outlet in the middle. Only the
control loop enters the box: two leads in series with the motor, to the
board’s two spade tabs, with the off switch in one of them. The
cordset’s molded entry pushes through a 13.9 × 8.5 mm hole in a 4.4 mm
wall, pocketed into the right end wall above the handhold. Inside, its
steel clip, U down, goes on from above: push the molded entry in hard,
compressing it, until its groove clears the wall, then push the clip
down over the groove until its bump clicks into the dimple at the top of
the hole. The clip stretches the soft molding a little, and that holds
it tight. The entry sits beside the board’s tabs so that the cordset’s
78 mm leads reach with slack; the console checks this. Print
knee_entry_test first to try the fit; the wall thickness,
hole and dimple are settings.
iec. A fused IEC C14 inlet in the right
end wall feeds the controller directly, for machines whose motor and
light were hardwired to their original controller. The inlet is a
Qualtek 723W-X2/03 snap-in [3] (a 31.6 × 27.5 mm cutout in a 1.5 mm
panel, pocketed into the end wall), on its side above the board cover.
The Schurter 6200.4315 has the same cutout and fits too. Inside, the
fused line goes to the light and, through the board and the off switch,
to the motor; the leads go through the cord pass-through to a junction
under the bed: three Wago 221-413 lever connectors [4] (line, neutral,
switched motor) in a cradle on the cavity floor beside the pass-through.
The motor and light leads land there. A T2A slow-blow fuse covers a 1.3
A motor and the lamp. The console gives the junction’s height; check
that your machine’s mechanism clears it. The inlet’s depth behind the
panel varies by version (knee_iec_depth); check yours.
With the IEC inlet, the shaft can be earthed
(knee_earth). A post behind the shaft’s end takes an M3
insert. Screw a strip of brass or phosphor bronze to it, with the earth
lead’s ring terminal, bent so its free end bears on the end of the
shaft. Contact through the oily bushings isn’t reliable, and the bar,
hub and shaft are metal you touch.
bare. A bare cord through a slot in the
end wall, gripped inside by a printed clamp bar (part
knee_cord_clamp) over a ridged saddle.
9.9 Assembly order
Fit the heat-set inserts: the board boss, the two cover bosses, the
two in the front face for the spring housing, and the earth post or
cord-clamp bosses if you have them.
Press the two bushings in, flanges forward: one into the front wall
from outside, one into the bulkhead from the front.
Press the idler pin into the bulkhead from the front, through its
boss, flush with the bulkhead’s back face.
Mount the switch on the bulkhead, lying under the shaft, lever up;
leave the screws loose.
Mount the pot behind the bulkhead (lug in its hole, nut and
lockwasher on the front) and solder its leads.
Slide the idler onto its pin, gear toward the bulkhead, and push the
retaining nut on in front of it.
Slide the shaft in from the front through the front bushing and the
sector (teeth toward the idler, cam down, hub toward the bulkhead), and
into the bulkhead’s bushing. Snug the sector’s set screw on its
flat.
Put the captive nuts in the spring housing (from below in the floor,
from above in the roof) and run the stop screw up from below; leave the
rest screw out. Drop the spring onto the floor’s spigot and the cap onto
the spring, spigot down. Screw the housing to the front face, its tongue
in the pocket.
Press the crank pin through the hub’s crank, centered, standing
about 1 mm proud of the crank’s bottom edge. Fit the hub onto the
shaft’s front end with the crank tilted up a few degrees, so that its
tip goes in through the housing’s front opening above the cap, and
tighten the hub’s set screw. The spring now pushes the crank up.
Run the rest screw down through the roof until it holds the crank
where you want the bar to rest (the spring’s preload).
Set the stop screw so the pin meets it at 2.25” of knee travel, and
lock both screws with their jam nuts.
Adjust the switch and the sector (above), then fit the pot’s pinion
and set the pot (above).
Wire the board and the power entry; screw the board down and fit the
cover. For iec, wire the junction under the bed.
Plug the bar into the hub.
9.10 Settings
The settings are in the Knee controller section. The ones
you are most likely to change:
knee_push: which way the knee pushes
the bar (right by default). The spring housing moves to the other side
of the hub, and the switch, the cam and the gears’ teeth follow.
knee_bar_drop, knee_travel_on,
knee_travel, knee_travel_max: the
bar’s drop below the shaft (12.5”), and the knee travel where the motor
starts (1”), for full speed (2”) and at the hard stop (2.25”).
knee_force_rest,
knee_force_rate: the knee force at rest and how
fast it rises.
knee_spring, knee_spring_rate,
knee_spring_max, knee_crank_r: the
return spring and the crank.
knee_ratio, knee_gear2_teeth,
knee_pinion2_teeth: the gearing.
knee_idler_angle,
knee_pot_angle: where the idler sits around the
shaft (10° above the horizontal), and the pot around the idler (120°
below the horizontal, toward the shaft), which keeps the pot clear of
the right wall and the floor.
knee_board_screw,
knee_board_turn: the board’s posts and
orientation.
knee_power: cordset, IEC inlet or bare
cord; knee_entry_pos and
knee_entry_z place the entry.
knee_motor_amps: over 1 A adds the
cover vents and the heatsink note.
knee_view: in part
knee_assembly, shows the mechanism at rest (0) or at the
stop (1).
9.11 References
Bourns, 91, 92, 93, 94, 95, 96, 97, 99 – 5/8” Square Single-Turn
Panel Control datasheet (91 to 99 series), via alldatasheet.com.
Product listing for 91A1A-B28-A25L: Master
Electronics.
Omron, SS Subminiature Basic Switch, Cat. No. B032-E1-14:
omronfs.omron.com.
Qualtek, 723W-X2/03 universal snap-in inlet with
fuseholder: Digi-Key
(ratings, panel thickness) and its drawing
(panel cutout). Alternative: Schurter 6200.4315, Digi-Key.
WAGO 221-413 lever connector, 3-conductor, 18.8 × 18.8 × 8.6 mm,
0.2–4 mm² (24–12 AWG): automa.net.
McMaster-Carr precision compression springs, 9001T46: mcmaster.com.
10 Parameter reference
This chapter is generated from the comments in
scad/vsm_base.scad by tools/extract_params.py.
Do not edit it by hand; change the comment in the model and rebuild.
There are 595 parameters; 591 of them appear in the Customizer. The
rest are lists the Customizer cannot show, and are marked edit in
the file.
Small-compartment option (“none” = base fitted to the bed alone)
Choices: none, storage, outlet, knee, controller.
compartment_mount
"built-in"
How the small compartment joins the base: built-in (one body with
the base), or attached (a separate bay screwed to the base’s right end,
for beds too long to print with a built-in compartment; storage only,
for now) Choices: built-in, attached.
hinge_type
"lollipop"
Hinge type Choices: lollipop, printed, barrel, none.
split
true
Split into two dovetailed halves for printing
10.3 Machine
Parameter
Default
Description
machine
"Singer 99K"
Your machine. A listed machine supplies every setting in the “Custom
machine” section; choose Custom to use those settings instead.
Choices: Singer 99K, Kenmore 158-14001, Custom.
bed_cushion_in
0.0625
Bed cushion thickness, compressed, in inches (1/16”); for a machine
standing on its feet, the pads under the feet
IGNORED unless machine = Custom. Thickness of the flat bed plate,
inches (99K: 5/16”)
custom_hinge_hole_inset_in
1.4375
IGNORED unless machine = Custom. Hinge hole center from each end of
the bed, inches (99K: 1 7/16”)
custom_hinge_hole_drop_in
0.375
IGNORED unless machine = Custom. Hinge hole center below the bed top
surface, inches (99K: 3/8”)
custom_hinge_pin_d_mm
7.14375
IGNORED unless machine = Custom. Hinge hole diameter, mm: the
printed hinge’s pin (99K: 9/32”)
custom_hinge_pin_engage_mm
12
IGNORED unless machine = Custom. How far the printed hinge’s pin
goes into the hinge hole, mm (no more than the hole’s depth)
custom_hinge_hole_depth_mm
22
IGNORED unless machine = Custom. Depth of the shallower hinge hole,
mm (0 = not measured): it limits how long a printed hinge’s pin may
be
custom_bed_flush
false
IGNORED unless machine = Custom. Bed top flush with the base’s rim
(true) or standing above it by the plate less rabbit_depth (false, as
for the 99K)
custom_foot_height_mm
0
IGNORED unless machine = Custom. A machine that stands on its own
feet: from the plate’s underside to the feet’s bottoms, mm (0 = the bed
rests on the ledge instead)
custom_cord_slot
[0, 0, 0, 0]
IGNORED unless machine = Custom. Slot through the back rim for cords
leaving the casting, mm: [center from the bed’s left end, width, slot
bottom below the bed’s top, height of the cords’ channel left under the
slot’s trim]; all zeros = none
custom_tilt_prop_mm
[152.4, 25.4]
IGNORED unless machine = Custom. Tilt prop, mm: [height above the
table of what rests on it (the arm’s underside) with the machine tipped
back to 90 degrees, cradle radius for a round arm (0 = a flat, level
top)]; height 0 = not measured
custom_back_trench
[0, 0, 0, 0]
IGNORED unless machine = Custom. Back bobbin trench, mm: [center
from the bed’s left end, width, length back from the bed edge, depth];
all zeros = none
custom_left_trench
[83.34, 57.6, 40, 2.5]
IGNORED unless machine = Custom. Left bobbin trench, mm: [center
from the bed’s front edge, width, length left from the bed edge, depth];
all zeros = none
custom_base_lid_notch
[8, 23]
IGNORED unless machine = Custom. Notch in the base lid’s left edge
clearing the motor boss as the lid opens, mm: [depth, width]; [0, 0] =
none
custom_relief_1_edge
"left"
IGNORED unless machine = Custom. Casting relief 1: which edge of the
bed the thickened area is on (none = not used) Choices: none, left,
right, back, front.
custom_relief_1
[83.34, 76.2, 15]
IGNORED unless machine = Custom. Casting relief 1, mm: [center,
length, thickness]. Center is along the edge from the bed’s left end
(back/front edges) or front edge (left/right edges); thickness is
measured down from the bed top
Printer build volume, for the size check and the print plates
printer_margin
8
Keep parts this far inside the bed’s edges (room for supports, brims
and skirts) Range 0 to 30, step 1.
print_plate
0
Print plates (part all): 0 = every plate, laid out side by side; N =
plate N only Range 0 to 30, step 1.
purge_tower_size
40
Purge tower kept clear on plates with supported parts (square, mm);
0 = none Range 0 to 80, step 5.
plate_gap
8
Space between parts on a plate Range 2 to 30, step 1.
10.6 Extensions
Parameter
Default
Description
back_ext
true
Include the back extension (outfeed support / compartment)
left_ext
true
Include the left extension
corner_ext
true
Include the left-rear corner piece (needs both of the above)
back_ext_length
240
Back extension length (X), from the base’s left face
back_ext_depth
100
Back extension body depth (Y), behind the base Range 100 to 300,
step 0.5.
left_ext_width
100
Left extension body width (X), left of the base Range 100 to
300, step 0.5.
left_ext_double
false
Left extension and corner: make the width for an outer bin matching
the inner one (overrides left_ext_width)
back_ext_double
false
Back extension and corner: make the depth for an outer bin matching
the inner one (overrides back_ext_depth)
left_ext_layout
"1+1"
Left extension past 100 mm: its outer bin whole (1+1), or split in
two along its length (1+2) Choices: 1+1, 1+2.
back_ext_layout
"1+1"
Back extension past 100 mm: its outer bin whole (1+1), or split in
two along its length (1+2) Choices: 1+1, 1+2.
corner_layout
"2x2"
Corner piece past 100 mm: the bobbin bin stays in the inner corner,
and the rest becomes open bins left of it and behind it; with both, the
far corner gets its own bin (2x2), or the left or back bin runs the full
length Choices: 2x2, long left, long back.
ext_divider
2.5
Divider wall between bins Range 1.2 to 6, step 0.1.
ext_bin_min
10
Least bin width inside; a narrower strip is left solid Range 5
to 30, step 0.5.
back_lids
"one"
Lids: one over each piece, or one per bay (on rabbets in the
dividers’ tops) Choices: one, per bay.
left_lids
"one"
Choices: one, per bay.
corner_lids
"one"
Choices: one, per bay.
bin_lid_type
"lift-out"
Per-bay lids on the outer bins: type (the inner bay’s lid keeps its
piece’s settings) Choices: lift-out, hinged, none.
bin_lid_hinge
"back"
Per-bay lids on the outer bins: hinge edge Choices: left, right,
front, back.
bin_lid_min
15
Least lid: a bin narrower than this inside gets no lid of its own
Range 10 to 40, step 1.
ext_divider_notch
true
Finger notch at the middle of each divider, for reaching into narrow
bins (one lid only)
ext_notch_w
30
Finger notch width and depth Range 10 to 60, step 1.
ext_notch_d
20
Range 5 to 60, step 1.
ext_gap
0.3
Gap between an extension body and the base or another extension
lip_clearance
0.2
Clearance between the lip and the base top
lip_min_t
5.4
Least lip thickness: where the bed stands less than this above the
rim (a bed set flush, say), the rim is cut down under the lips so they
keep it, and trim strips (parts back_trim, left_trim) fill the cuts when
the extensions are off Range 3 to 10, step 0.1.
lip_cut_clearance
0.25
Clearance around the recessed lips and the trims, per side Range
0.1 to 0.6, step 0.05.
ext_top_adjust
0
Trim to the extensions’ top plane (lids, lips, trenches) against the
real bed, mm; negative lowers it Range -3 to 3, step 0.1.
ext_floor
3
Extension floor thickness Range 1.5 to 8, step 0.1.
ext_standard
true
Standard extension height: every extension’s top at ext_height above
the table, with the same bays (the base is raised, or the extensions
stand on podiums, to match the bed)
ext_height
88.225
Standard extension height: the 99K’s bed top Range 60 to 140,
step 0.005.
podium_min
5
Least podium under an extension, when the bed stands above
ext_height Range 3 to 20, step 0.5.
podium_wall
6
Podium wall (it is a frame, open below) Range 3 to 15, step
0.5.
ext_frame
4
Frame width around each lid, at the top Range 2 to 10, step
0.1.
ext_ledge
4
Ledge the lid rests on, inside the frame Range 2 to 10, step
0.1.
ext_lid_thickness
4
Lid thickness (= depth of the lid rabbet) Range 2 to 8, step
0.1.
ext_lid_clearance
0.3
Clearance around the lid in its rabbet, per side
ext_hinge_margin
0.5
Hinged lids: the ledge on the hinge side is widened so the open lid
stays this far clear of the bay
ext_finger_hole
22
Finger hole in each lid
ext_rounding
3
Rounding of the extensions’ exposed edges Range 0 to 8, step
0.5.
10.7 Freestanding boxes
Parameter
Default
Description
make_back_box
false
Also make a freestanding version of the back extension (part
back_box): same bay and lid, no lip, pegs or dovetails
make_left_box
false
Also make a freestanding left box (part left_box)
make_corner_box
false
Also make a freestanding corner box (part corner_box)
10.8 Lid hinges
Parameter
Default
Description
base_lid_hinge
"right"
Lid edge each lid hinges on Choices: left, right, front,
back.
back_lid_hinge
"back"
Choices: left, right, front, back.
left_lid_hinge
"left"
Choices: left, right, front, back.
corner_lid_hinge
"back"
Choices: left, right, front, back.
base_lid_type
"hinged"
Base compartment lid: hinged (snap-in dimple hinge), lift-out (plain
lid resting on the ledge), or none (rabbet left for a lid later)
Choices: hinged, lift-out, none.
back_lid_type
"hinged"
Back extension lid type Choices: hinged, lift-out,
none.
left_lid_type
"hinged"
Left extension lid type Choices: hinged, lift-out,
none.
corner_lid_type
"hinged"
Corner piece lid type Choices: hinged, lift-out, none.
base_lid_style
"solid"
Base compartment lid style: solid, or perforated for ventilation
Choices: solid, perforated.
back_lid_style
"solid"
Back extension lid style Choices: solid, perforated.
left_lid_style
"solid"
Left extension lid style Choices: solid, perforated.
corner_lid_style
"solid"
Corner piece lid style Choices: solid, perforated.
base_lid_grip
"finger hole"
Base compartment lid grip: finger hole, or a thumb tab reaching over
a notch in the wall Choices: finger hole, tab.
base_lid_tab_edge
"front"
Base lid tab edge (front only is practical, on a lift-out lid)
Choices: front, back, left, right.
back_lid_grip
"finger hole"
Back extension lid grip Choices: finger hole, tab.
back_lid_tab_edge
"right"
Back lid tab edge (back or right) Choices: front, back, left,
right.
left_lid_grip
"finger hole"
Left extension lid grip Choices: finger hole, tab.
left_lid_tab_edge
"front"
Left lid tab edge (front or left) Choices: front, back, left,
right.
corner_lid_grip
"finger hole"
Corner piece lid grip Choices: finger hole, tab.
corner_lid_tab_edge
"left"
Corner lid tab edge (left or back) Choices: front, back, left,
right.
grip_tab_w
25
Thumb tab width
grip_tab_over
1.5
Thumb tab overhang past the outer face
grip_tab_r
2
Thumb tab corner radius Range 0 to 5, step 0.5.
grip_scoop_d
2.5
Thumb scoop below the tab: depth into the outer face
grip_scoop_h
6
Thumb scoop height below the lid Range 2 to 12, step
0.5.
base_lid_notch_r
4
Base lid motor-boss notch (size from the machine profile): inner
corner radius Range 0 to 10, step 0.5.
base_lid_notch_flare
10
Notch: radius blending it into the lid edge
base_lid_notch_offset
0
Notch: front-to-back offset from the middle of the lid Range -50
to 50, step 0.5.
lid_perf_d
5
Perforation hole diameter Range 2 to 12, step 0.5.
lid_perf_pitch
8
Perforation pitch (hex grid) Range 4 to 20, step 0.5.
lid_perf_margin
6
Solid margin kept around the lid’s edges, finger hole and hinge
Range 2 to 20, step 0.5.
lid_bump_d
3
Hinge bump diameter at its base Range 1.5 to 6, step
0.1.
lid_bump_engage
1.0
How far each bump engages the wall
lid_tab_len
15
Flex tab carrying each bump: length along the end
lid_tab_w
4
Flex tab width Range 1.5 to 8, step 0.1.
lid_slot_w
1
Slot that frees the flex tab Range 0.5 to 3, step 0.1.
lid_bump_angle
35
Bump flank angle from its axis: smaller is steeper and holds better
(45 = the v19 cone) Range 15 to 60, step 1.
lid_hinge_end_clearance
0.15
Clearance at the lid’s two hinge ends (less end float keeps both
bumps engaged)
lid_recess_clearance
0.075
Clearance between bump and recess, per side
lid_open_stop
true
Cut a chamfer behind the hinge so an open lid leans back and stays
up
10.9 Ruler and logos (front, back
and bottom)
Parameter
Default
Description
ruler
false
A ruler across the base’s front face, from where the left corner’s
round-over ends to where the right one’s begins (on the base and a
built-in compartment; not on an attached bay or the extensions)
ruler_scale_1
"inch"
Scales, from the bottom up: inch, centimeter, custom, or none
Choices: inch, cm, custom, none.
ruler_scale_2
"cm"
Choices: inch, cm, custom, none.
ruler_scale_3
"none"
Choices: inch, cm, custom, none.
ruler_bottom
5
The ruler’s bottom edge above the bottom of the base Range 0 to
40, step 0.5.
ruler_scale_h
8
Height of each scale Range 5 to 15, step 0.5.
ruler_inch_div
8
Inch scale: divisions per inch, and a longer tick every so many (8
and 2: eighths, longer at the quarters; 10 and 5: tenths, longer at the
half) Range 1 to 32, step 1.
ruler_inch_mid
2
Range 1 to 16, step 1.
ruler_cm_div
10
Centimeter scale: divisions per cm, and a longer tick every so many
Range 1 to 20, step 1.
ruler_cm_mid
5
Range 1 to 10, step 1.
ruler_custom_unit
10
Custom scale: the numbered unit in mm, its divisions, a longer tick
every so many, and its name (blank for none) Range 1 to 100, step
0.01.
ruler_custom_div
10
Range 1 to 32, step 1.
ruler_custom_mid
5
Range 1 to 16, step 1.
ruler_custom_name
""
ruler_number_every
1
Number every this many units (1 = every inch, every cm) Range 1
to 10, step 1.
ruler_text_size
3.5
Lettering size Range 2 to 6, step 0.1.
ruler_line_w
0.6
Narrowest line in the ruler, ticks and lettering alike (keep it at
or over your nozzle’s width) Range 0.3 to 1.2, step 0.05.
logo_left
""
Logo files (SVG: clean outlines, no self-crossing paths) for the
face’s upper left and upper right corners, relative to this file’s
folder or a full path; blank for none
logo_right
""
logo_size
[25, 15]
Each logo is stretched to this box, width and height (set it to the
logo’s own proportions)
logo_inset
6
Logos’ distance in from the face’s flat ends and down from where the
top’s round-over ends Range 0 to 40, step 0.5.
back_logo_left
""
Back face: SVGs near its lower left and lower right corners, as you
look at the back (so the left one is at the base’s right end); for a
maker’s name, model, serial number, date. Blank for none
back_logo_right
""
back_logo_size
[40, 15]
Each back logo is stretched to this box, width and height
back_logo_inset
6
Back logos’ distance in from the face’s flat ends (clear of the
harness rods’ holes) and up from the bottom Range 0 to 40, step
0.5.
bottom_logo_left
""
Bottom: SVGs centered on the left and right halves of the base
(where it splits, whether or not it is split), as you look at the bottom
with the base tipped back onto its back edge. Blank for none
bottom_logo_right
""
bottom_logo_size
[80, 40]
Each bottom logo is stretched to this box, width and height
face_relief
"raised"
Ruler and logos on the front and back: raised from the face,
engraved into it, or inlaid (engraved and filled flush). Raised and
inlaid marks are color-tagged for another filament: each mark and the
base its own random color (export 3MF to keep them; needs an OpenSCAD
with the Manifold backend) Choices: raised, engraved,
inlaid.
bottom_relief
"engraved"
The bottom’s logos: engraved, or inlaid (color-tagged). Not raised:
the base prints standing on its bottom Choices: engraved,
inlaid.
face_relief_depth
0.6
How far they stand out or cut in Range 0.3 to 2, step
0.1.
face_relief_chamfer
true
Slope the marks’ overhangs at 45 degrees: under a raised mark’s
downward-facing edges, over an engraved recess’s upward-facing ones
(they print as a flat overhang that curls without it). Not for inlaid
marks, which are filled
face_color_seed
7
Change it for another set of random colors Range 0 to 999, step
1.
10.10 Handholds
Parameter
Default
Description
handholds
true
Handholds under each end
handhold_bottom_len
76.2
Handhold length along the end, at the bottom face (3”)
handhold_top_len
50.8
Handhold length at its top (2”)
handhold_height
12.7
Handhold height above the bottom face (1/2”)
handhold_depth
15.875
Handhold depth into the end wall (5/8”)
handhold_lip_flat
4
Flat underside of the lip at the face, before the ceiling climbs
Range 0 to 10, step 0.5.
handhold_lip_round
2
Radius rounding the lip’s outer edge Range 0 to 6, step
0.5.
handhold_knockout
true
Knock-out wall under the lip, removed after printing
knockout_t
1.2
Knock-out wall thickness
knockout_gap
0.2
Gap between the knock-out wall and the lip
knockout_tab
true
Breakaway tab tying one end of the knock-out wall to the pocket
end
knockout_tab_h
0.8
Tab height (the tab sits just under the lip gap)
knockout_brim
true
Brim around the foot of each knock-out wall, so it stands until the
tab joins it
knockout_brim_w
5
Brim width each side of the wall
knockout_brim_h
0.2
Brim height (about one first layer)
10.11 Harness rods
Parameter
Default
Description
harness_rods
true
Rod notches and rods either side of each handhold
rod_d
4.7625
Rod diameter (3/16”)
rod_hole_d
4.95
Rod hole diameter (printed as a teardrop, point up)
rod_x
7
Rod center in from the end face Range 3 to 15, step
0.1.
rod_z
7
Rod center above the bottom face Range 3 to 15, step
0.1.
notch_len
25
Notch length along the rod
notch_clear
4
Clear space around the rod in the notch, behind and above it
Range 1 to 10, step 0.5.
notch_inset
25
Distance from each outer face (front, back) to its notch
rod_stop
5
Material left between a rod’s blind end and the handhold
rod_plug_len
5
Printed plug closing the open end of each rod hole (0 = no plugs;
rods run to the face) Range 0 to 10, step 0.5.
rod_plug_clearance
0.1
Plug clearance in the hole, per side (the crush ribs make the press
fit)
rod_plug_rib
0.15
Crush rib interference, beyond the hole wall
10.12 Turn button
Parameter
Default
Description
turn_button
false
Turn button on the front rim that holds the bed’s front edge down
(off by default)
turn_button_x
0
Position along the front rim (X); 0 = automatic, between the split
and the compartment
turn_button_overlap
4
How far the button reaches over the bed’s front edge Range 1 to
10, step 0.5.
turn_button_w
9
Button width Range 6 to 16, step 0.5.
turn_button_t
4
Button thickness Range 2 to 8, step 0.5.
turn_button_gap
0.3
Gap between the button and the bed top
turn_button_ease
10
Easing: how far the pad’s smooth slopes run out along the rim, each
side
turn_button_swell
3
How far the pad swells out of the front face, enclosing the nut
Range 0 to 8, step 0.5.
turn_button_swell_taper
10
Below the nut, the swelling blends back into the front face over
this height
turn_button_nut_spec
"#8-32"
Nut for the button screw (BOSL2 spec)
10.13 Inserts
Parameter
Default
Description
ins_spacing
10
Spacing between parts in the insert print layouts Range 0 to 50,
step 1.
bobbin_d
20.6375
Bobbin diameter (class 15 and 66: 13/16”), for the bobbin trays and
the spool tray
bobbin_t
11.1125
Bobbin thickness (class 15 and 66: 7/16”)
10.14 Bobbin trays (corner
bay)
Parameter
Default
Description
bb_trays
0
Number of trays, bottom included; 0 = as many as fit under the lid
Range 0 to 10, step 1.
bb_post_d
5
Post diameter (class 15 and 66 bores are a little over 6 mm)
Range 3 to 10, step 0.1.
bb_grid
[3, 3]
Post grid [columns (X), rows (Y)]; cells that would crowd the center
column are left empty
bb_floor
3
Tray floor thickness Range 1.2 to 6, step 0.1.
bb_bobbin_clear
1
Clearance between a bobbin’s top and the tray above Range 0 to
4, step 0.1.
bb_wall_clear
0.75
Clearance between the trays and the bay walls, per side Range
0.2 to 3, step 0.05.
bb_corner_r
2
Tray corner radius Range 0 to 10, step 0.5.
bb_top_clear
1
Clearance between the top of the knob and the lid Range 0 to 5,
step 0.1.
bb_lighten
true
Lightening holes where four cells meet
bb_lighten_d
12
Lightening hole diameter Range 4 to 20, step 0.5.
bb_pin_d
3
Pin on each post tip: diameter Range 1.5 to 6, step
0.1.
bb_pin_h
2
Pin height above the post shoulder Range 0.5 to 5, step
0.1.
bb_socket_clear
0.2
Socket clearance around the pin, per side Range 0 to 1, step
0.05.
bb_socket_extra
0.4
Socket depth beyond the pin Range 0 to 2, step 0.1.
bb_socket_chamfer
0.6
Chamfer at the socket mouth (also absorbs elephant’s foot) Range
0 to 2, step 0.1.
bb_column_d
12
Handle column diameter Range 6 to 20, step 0.5.
bb_column_flare
2
Flare radius at the column’s foot Range 0 to 5, step
0.5.
bb_knob_d
18
Knob diameter Range 8 to 30, step 0.5.
bb_knob_h
8
Knob height Range 3 to 20, step 0.5.
bb_hole_clear
0.5
Clearance between the knob and the upper trays’ center holes, per
side Range 0.1 to 2, step 0.05.
10.15 Notion trays (back or left
bay)
Parameter
Default
Description
ot_bay
"back"
Bay the notion and spool trays go in Choices: back,
left.
ot_custom_h
12
Custom tray height Range 5 to 80, step 0.5.
ot_show
[25, 20, 15, 10]
Tray heights shown stacked in part notion_assembly
ot_wall_clear
1
Clearance between the trays and the bay walls, per side Range
0.2 to 3, step 0.05.
ot_wall
1.2
Wall thickness Range 0.8 to 4, step 0.1.
ot_floor
1.6
Floor thickness Range 0.8 to 4, step 0.1.
ot_corner_r
2
Outer corner radius Range 0 to 10, step 0.5.
ot_boss
9
Corner boss size (square, from the outer corner) Range 5 to 20,
step 0.5.
ot_pin_d
3
Pin diameter Range 1.5 to 6, step 0.1.
ot_pin_h
2
Pin height above the wall tops Range 0.5 to 5, step
0.1.
ot_socket_clear
0.2
Socket clearance around the pin, per side Range 0 to 1, step
0.05.
ot_socket_extra
0.4
Socket depth beyond the pin Range 0 to 2, step 0.1.
ot_socket_chamfer
0.5
Chamfer at the socket mouth (also absorbs elephant’s foot) Range
0 to 2, step 0.1.
ot_grip_w
40
Finger-hold lip length along each end wall Range 10 to 120, step
1.
ot_grip_reach
5
How far the lip reaches in from the wall Range 0 to 15, step
0.5.
ot_grip_t
1.5
Thickness of the lip at its top, above the 45-degree underside
Range 0.8 to 4, step 0.1.
ot_top_clear
1
Clearance between the top tray’s pins and the lid Range 0 to 5,
step 0.1.
10.16 Notion tray compartments
Parameter
Default
Description
ot_compartments
false
Divide the plain notion trays (not the spool tray) into
compartments
ot_cell
50.8
Target compartment size; the grid divides the tray evenly to come
closest to it (2” gives 2 x 4 in the back or left bay; 1” gives 3 x 8)
Range 10 to 100, step 0.1.
ot_cols
0
Compartments along the tray’s length (0 = from ot_cell) Range 0
to 20, step 1.
ot_rows
0
Compartments across the tray’s width (0 = from ot_cell) Range 0
to 20, step 1.
ot_divider_frac
0.8
Divider height, as a fraction of the tray height Range 0.2 to 1,
step 0.05.
ot_divider_t
1.2
Divider thickness Range 0.8 to 4, step 0.1.
10.17 Spool tray
Parameter
Default
Description
ot_spool_d
38
Spool diameter Range 20 to 80, step 0.5.
ot_spool_h
44
Spool height Range 20 to 100, step 0.5.
ot_spool_post_d
5
Post diameter at the top, through the bobbin Range 3 to 15, step
0.1.
ot_spool_post_base_d
7
Post diameter at the floor; the post tapers to the top diameter at
the spool top Range 3 to 20, step 0.1.
ot_spool_bore
7.5
Smallest spool bore you expect (for the console check) Range 3
to 20, step 0.1.
ot_spool_gap
1.5
Space between neighboring spools Range 0 to 10, step
0.1.
ot_spool_wall_gap
0.5
Space between the spools and the tray walls and corner bosses
Range 0 to 5, step 0.1.
ot_spool_top_clear
1
Clearance between the bobbin tops and the tray above Range 0 to
5, step 0.1.
ot_spool_open_sides
true
Cut the long side walls down to a curb between the corner bosses, so
the spools can be grasped from the side
ot_spool_curb
14
Curb height left along the long sides (it stiffens the floor when
the tray is lifted by its ends) Range 3 to 40, step 0.5.
ot_spool_cut_r
5
Radius at the bottom corners of the cutaway Range 0 to 20, step
0.5.
10.18 Tray gussets
Parameter
Default
Description
ot_gussets
true
Small triangular ribs at the foot of the trays’ long walls, where a
thin wall meets the floor at one layer line
ot_gusset_t
1
Gusset thickness (on the spool tray it must fit between neighboring
spools) Range 0.6 to 3, step 0.1.
ot_gusset_d
5
Gusset reach along the floor, from the wall Range 1 to 15, step
0.5.
ot_gusset_h
8
Gusset height up the wall (less on low trays) Range 1 to 20,
step 0.5.
ot_gusset_pitch
40
Spacing to aim for between gussets on plain trays Range 15 to
120, step 1.
10.19 Small compartment
Parameter
Default
Description
storage_inner_length
70
Inner length of the small compartment (X)
lid_ledge
10
Lid ledge width around the small compartment Range 5 to 20, step
0.5.
10.20 Outlet compartment
Parameter
Default
Description
outlet_size
[76, 40, 22]
Outlet body, mm: [length, width, thickness]. Modern: 76 x 40 x 22;
early Bakelite: 83 x 45 x 22
outlet_receptacle_spacing
34
Receptacle spacing, center to center (modern 34, Bakelite 38)
Range 20 to 60, step 0.5.
outlet_clearance
1.5
Clearance around the outlet inside its curbs, per side
outlet_y_offset
0
Outlet center, front-to-back offset from the middle of the
compartment Range -50 to 50, step 0.5.
outlet_curb_h
3
Height of the curbs on the floor around the outlet Range 1 to 8,
step 0.5.
outlet_curb_w
3
Width of the curbs Range 1 to 8, step 0.5.
outlet_mount
"through"
How the outlet is held: a heat-set insert in the end wall (needs a
soldering iron), or a flat-head screw through the end wall from outside,
with a nut on the outlet’s face Choices: through, insert.
outlet_screw_spec
"#8-32"
Screw through the outlet’s center hole (drill out the membrane)
outlet_screw_hole_d
4.6
Through mount: clearance hole for the screw
outlet_screw_head_d
8.4
Through mount: flat-head diameter (#8: 8.4)
outlet_screw_cap
true
Through mount: recess the head under a printed cap (part
outlet_cap)
outlet_cap_d
12
Through mount: cap diameter Range 9 to 20, step 0.5.
outlet_cap_t
2
Through mount: cap thickness Range 1 to 4, step 0.1.
outlet_insert_d
5.6
Hole for the heat-set insert in the right end wall (use the insert
maker’s recommended diameter)
outlet_insert_depth
12
Depth of the insert hole into the wall Range 4 to 20, step
0.5.
outlet_labels
true
Recess the receptacle names into the floor in front of the
outlet
outlet_light_side
"back"
Receptacle wired always on (the light); the other is the controlled
motor output Choices: back, front.
outlet_light_label
"LIGHT"
Name for the always-on receptacle
outlet_motor_label
"MOTOR"
Name for the controlled receptacle
outlet_label_size
7
Letter height Range 3 to 12, step 0.5.
outlet_label_depth
0.6
Recess depth Range 0.2 to 2, step 0.1.
outlet_lid_hinge
"left"
Edge the outlet-compartment lid hinges on Choices: left, right,
front, back.
outlet_slot_1_side
"front"
Cord slot 1: lid edge it opens from Choices: none, front, right,
back.
outlet_slot_2_side
"back"
Cord slot 2: lid edge it opens from Choices: none, front, right,
back.
outlet_slot_1_pos
0
Slot 1 position along its edge, mm from the lid’s left end
(front/back edges) or front end (right edge); 0 = automatic
outlet_slot_2_pos
0
Slot 2 position along its edge; 0 = automatic
outlet_slot_w
9
Cord slot width Range 4 to 20, step 0.5.
outlet_slot_depth
25
Cord slot depth in from the lid edge
outlet_slot_chamfer
1.5
Chamfer on the slot’s top edges, easing a cord pulled over them
outlet_cord_exit
"lid"
Where the outlet’s two cords leave the compartment: through the
lid’s slots (lid); through slots in the walls, the power cord (from the
outlet’s back end) out the back and the controller cord (from its front
end) out the front (front_rear); or both out the back, the controller
cord running back in a channel in the floor (rear). The wall slots take
trims (part outlet_trims) that leave an eased opening for the cord
Choices: lid, front_rear, rear.
outlet_cord_z
0
Where the cords leave the outlet’s ends: height above the floor (0 =
half the outlet’s height), and the cord’s centre from the outlet’s back,
against the end wall (0 = 4.7: a cordset outlet’s cords leave its ends
at the center, 1/8” up from its back) Range 0 to 60, step
0.5.
outlet_cord_x
0
Range 0 to 40, step 0.1.
outlet_wall_slot_w
9
Wall slots: width, and the opening left under the trim for the cord
Range 5 to 16, step 0.5.
outlet_cord_gap
7
Range 4 to 14, step 0.5.
outlet_channel_w
3.8
Floor channel for the controller cord (rear): width and depth, for
two-wire lamp cord standing on edge (about 3 x 6 mm) Range 2.5 to 8,
step 0.1.
outlet_channel_depth
7
Range 4 to 10, step 0.5.
outlet_clip
0.7
Retention lips along the channel, alternate sides: overhang, and
spacing along the path Range 0.3 to 1.5, step 0.1.
outlet_clip_pitch
25
Range 10 to 60, step 1.
10.21 Knee controller
Parameter
Default
Description
knee_push
"right"
The knee controller (compartment_option = “knee”): a knee bar turns
a shaft running front to back in the right bay. A crank on the bar’s
hub, outside the front face, pushes a compression spring in a housing
beside it; steel screws in the housing set the rest and the hard stop,
so the knee’s force stays out of the shaft and gears. Inside, two gear
stages turn a pot standing in for the donor board’s slide pot, and a cam
on the sector works a switch that cuts the motor for the first part of
the travel. See the User’s Guide before building: the board is live at
mains voltage. Which way the knee pushes the bar Choices: right,
left.
knee_bar_drop
317.5
Bar: drop from the shaft to where the knee meets it (12.5” = 317.5
mm) Range 150 to 450, step 0.5.
knee_travel_on
25.4
Knee travel at that point where the switch closes and the motor
starts; the travel before it is dead (1” = 25.4 mm) Range 0 to 60,
step 0.5.
knee_travel
50.8
Knee travel at that point for full speed (2” = 50.8 mm) Range 20
to 100, step 0.5.
knee_travel_max
57.15
Knee travel at the hard stop (2.25” = 57.15 mm) Range 20 to 120,
step 0.5.
knee_force_rest
4.45
Knee force at rest (the spring’s preload), N (1 lb = 4.45 N)
Range 0.5 to 20, step 0.05.
knee_force_rate
0.263
Knee force rise, N per mm of knee travel (1.5 lb/in = 0.263)
Range 0.05 to 1, step 0.001.
knee_bar_square
9.525
Bar’s square end (3/8” = 9.525 mm) Range 5 to 16, step
0.025.
knee_bar_clearance
0.15
Clearance on the bar’s square end, per side Range 0 to 0.5, step
0.05.
knee_shaft_d
8
Shaft diameter Range 6 to 12, step 0.5.
knee_shaft_x
17
Shaft axis: distance from the divider Range 10 to 40, step
0.5.
knee_shaft_z
0
Shaft axis: height above the bay floor; 0 = middle of the bay
Range 0 to 60, step 0.5.
knee_bushing
[8, 12, 10]
Flanged bushings (2, front wall and bulkhead): [bore, outside
diameter, length]
knee_bushing_flange
[16, 2]
Bushing flange: [diameter, thickness]
knee_bushing_hole
12.1
Hole for a bushing’s sleeve (press fit; FDM holes print a little
small) Range 8 to 20, step 0.05.
knee_bulkhead_pos
36
Bulkhead (carries the rear bushing, the idler pin, the pot and the
switch): distance behind the front wall’s inside face Range 25 to
80, step 0.5.
knee_bulkhead_t
3
Bulkhead thickness where the pot mounts (the pot’s bushing must
reach through it and take the nut) Range 2 to 5, step 0.1.
knee_bulkhead_above
15
Bulkhead height above the shaft axis Range 5 to 30, step
0.5.
knee_gear_module
1
Gears: module (mm per tooth) Range 0.5 to 2, step
0.05.
knee_pinion_teeth
16
First stage: idler pinion teeth (driven by the sector on the knee
shaft) Range 12 to 30, step 1.
knee_ratio
4
First stage ratio, sector to idler pinion (the sector is cut from a
gear with ratio x pinion teeth) Range 2 to 8, step 1.
knee_gear2_teeth
47
Second stage: idler gear teeth (a sector on the idler, driving the
pot’s pinion) Range 20 to 80, step 1.
knee_pinion2_teeth
16
Second stage: pot pinion teeth Range 12 to 30, step 1.
knee_gear_face
5
Gear face width Range 3 to 10, step 0.5.
knee_gear_backlash
0.15
Tooth thinning per gear for backlash, at the pitch circle Range
0 to 0.5, step 0.05.
knee_gear_cd_extra
0.1
Extra center distance between the gears Range 0 to 0.5, step
0.05.
knee_idler_angle
10
Direction from the shaft to the idler, degrees (0 = straight right,
negative = down) Range -60 to 60, step 1.
knee_pot_angle
-120
Direction from the idler to the pot, degrees (-90 = straight down)
Range -180 to 0, step 1.
knee_pot_body
15.88
Pot (Bourns 91, 5/8” square): body size Range 10 to 25, step
0.01.
knee_pot_depth
22
Pot body depth behind the panel, with room for the pins and wires
Range 10 to 40, step 0.5.
knee_pot_hole
9.9
Pot bushing (3/8-32 UNEF): panel hole Range 6 to 14, step
0.05.
knee_pot_bushing_len
9.53
Pot bushing length Range 5 to 15, step 0.01.
knee_pot_shaft_d
6.35
Pot shaft diameter (1/4”) Range 3 to 8, step 0.05.
knee_pot_shaft_len
22.23
Pot shaft length from the mounting face (B28: 7/8”) Range 12 to
30, step 0.01.
knee_pot_lug_r
7.75
Pot anti-rotation lug: radius from the shaft (0.305”) Range 5 to
12, step 0.05.
knee_pot_lug_angle
90
Pot anti-rotation lug: direction from the shaft, degrees (90 = up);
turn the pot to suit Range -180 to 180, step 1.
knee_pot_lug_hole
2.6
Pot anti-rotation lug: hole diameter Range 1.5 to 4, step
0.1.
knee_pot_r
1000
Pot: total resistance, kOhm Range 10 to 5000, step 10.
knee_pot_travel
240
Pot: electrical travel, degrees Range 180 to 300, step
1.
knee_pot_mech
300
Pot: mechanical rotation, degrees (the end zones beyond the
electrical travel take the overtravel to the stop) Range 180 to 330,
step 1.
knee_r_span
220
Resistance span the board wants over the speed range (knee_travel_on
to knee_travel), kOhm; a linear placeholder until the board is measured
Range 10 to 2000, step 5.
knee_switch_body
[19.8, 10.2, 6.4]
Off switch (Omron SS-5GL), lying under the shaft, lever up: body
[length, height, thickness]
knee_switch_holes
[9.5, 2.9]
Switch mounting holes: pitch, and height above the bottom (terminal)
edge
knee_switch_op
8.8
Switch operating position, from the mounting-hole line (8.8 +/- 0.8)
Range 5 to 15, step 0.1.
knee_switch_md
0.8
Switch movement differential (release beyond the operating position)
Range 0.1 to 2, step 0.05.
knee_switch_press
0.3
How far past the operating position the cam holds the lever at rest
Range 0 to 1.5, step 0.05.
knee_switch_act
5.3
Actuating point: distance from the lever’s free end (Omron’s
drawing: 14.5 mm from the lever’s pivot end, so 5.3 from its free end)
Range 0 to 19, step 0.1.
knee_switch_floor
5
Switch body’s bottom (terminal) edge above the bay floor, with room
for the terminals and wires Range 2 to 15, step 0.5.
knee_switch_adjust
1.5
Adjusting slots for the switch: travel up and down Range 0 to 4,
step 0.1.
knee_switch_screw
2.4
Switch screw clearance (M2 or #2-56) Range 1.8 to 3, step
0.05.
knee_spring
[15.24, 1.83, 31.75]
Return spring (compression, standing in the housing beside the hub):
[outside diameter, wire diameter, free length] (McMaster 9001T46: 0.6”
OD, 0.072” wire, 1.25” long)
knee_spring_rate
7.88
Return spring: rate, N per mm (9001T46: 45 lb/in = 7.88) Range 1
to 50, step 0.01.
knee_spring_max
14.78
Return spring: its maximum deflection, mm (9001T46: 26 lb at 0.668”
long, 14.8 mm down) Range 3 to 40, step 0.01.
knee_crank_r
0
Crank radius, shaft to the crank pin; 0 = set from the spring rate
to give knee_force_rate Range 0 to 90, step 0.5.
knee_board
[75, 35]
Board (75 x 35 mm donor board): [length, width]
knee_board_screw
[49.6, 12.5]
Board screw: [along from the board’s notched end, across from the
long edge nearer the screw]; the peg and rest post follow from it
knee_board_turn
180
Board orientation: 180 = notched end toward the back of the bay,
spade tabs on the right; 0 = notched end forward, tabs on the left
Choices: 0, 180.
knee_board_tabs
[58, 70]
Spade tabs, on the long edge away from the screw: positions along
from the notched end
knee_board_tab_room
16
Room beside the board for the spade connectors and their wires
Range 8 to 30, step 0.5.
knee_board_mirror
false
Mirror the board’s posts across the board (for a board laid out the
other way round)
knee_board_h
8
Board underside above the floor Range 4 to 20, step
0.5.
knee_board_parts_h
13.6
Tallest part above the board underside Range 5 to 40, step
0.1.
knee_insert_d
4.6
Heat-set insert hole, M3 Range 3 to 6, step 0.05.
knee_power
"cordset"
How the controller is wired in: cordset = the standard pedal
cordset’s molded entry and clip (the control loop out to the cordset’s
junction); iec = fused IEC C14 inlet, with the motor and light wired at
a junction under the bed; bare = a bare cord through a slot, held by a
printed clamp Choices: cordset, iec, bare.
knee_motor_amps
1.0
Motor current (for the triac heating note and the cover vents)
Range 0.2 to 3, step 0.1.
knee_earth
true
Earth contact for the shaft: a post behind the shaft’s end for a
spring strip and the earth lead (iec)
knee_entry_hole
[13.9, 8.5]
Cordset entry: hole [width, height] (long side horizontal)
knee_entry_wall
4.4
Cordset entry: wall thickness at the hole Range 3 to 6, step
0.05.
knee_entry_dimple
[3.4, 2.4, 2.8]
Cordset entry: dimple for the clip’s bump, at the top of the hole
[width, height, depth from the inside]
knee_entry_clip
[21.4, 9.5]
Cordset entry: steel clip [width, height]
knee_entry_z
20
Cordset entry: hole center above the bay floor (its pocket must
clear the right handhold’s ceiling) Range 6 to 45, step
0.5.
knee_entry_pos
0
Cordset entry or IEC inlet: position from the bay’s back wall; 0 =
beside the board’s spade tabs Range 0 to 140, step 0.5.
knee_entry_lead
78
Cordset: lead length inside, from the molded face to the connector
tips Range 30 to 200, step 1.
knee_iec_cutout
[31.6, 27.5]
IEC inlet (Qualtek 723W-X2/03 snap-in, or Schurter 6200.4315,
mounted on its side): panel cutout [along the wall, height]
knee_iec_radius
1
IEC inlet: cutout corner radius Range 0 to 5, step
0.5.
knee_iec_panel
1.5
IEC inlet: panel thickness (723W-X2/03: 0.8 to 2 mm; 6200.4315: 1.5
mm) Range 0.8 to 2.5, step 0.1.
knee_iec_depth
40
IEC inlet: depth behind the panel, with its connectors (check your
inlet) Range 20 to 70, step 0.5.
knee_wago
[18.8, 18.8, 8.6]
Junction: Wago 221-413 lever connector [width, depth, height]
knee_wago_n
3
Junction: number of connectors (line, neutral, switched motor)
Range 1 to 6, step 1.
knee_cord
[7.5, 4.5]
Bare cord: [width, thickness] (flat SPT-2 about 7.5 x 4.5)
knee_cord_pos
14
Bare cord: position along the right end wall, from the bay’s back
wall Range 8 to 120, step 0.5.
knee_view
0
Part knee_assembly: how far the knee is pushed, 0 (rest) to 1 (hard
stop) Range 0 to 1, step 0.05.
10.22 Controller compartment
Parameter
Default
Description
ctrl_iec_tunnel
"left"
The controller compartment (compartment_option = “controller”): a
bay for the boards of an MCU or analog motor controller, with no knee
mechanism. A fused IEC C14 inlet stands in one of the two gabled tunnels
in the back wall behind the bay, a panel of low-voltage jacks (for a
pedal) closes the other, a sparse grid of posts on the floor takes the
boards, and knock-out walls close the pass-through to the machine cavity
until the motor’s leads need it. The wiring is left to the builder.
Back-wall tunnel for the IEC inlet, as seen from the front: left (beside
the divider and the pass-through, keeping the mains on that side) or
right; the jacks take the other Choices: left, right.
ctrl_iec_cutout
[27.5, 31.6]
IEC inlet, standing upright (Qualtek 723W-X2/03 or Schurter
6200.4315 turned on end): panel cutout [width, height]
ctrl_iec_radius
1
IEC inlet: cutout corner radius Range 0 to 5, step
0.5.
ctrl_iec_panel
1.5
IEC inlet: panel thickness left at the back of its tunnel
(723W-X2/03: 0.8 to 2 mm; 6200.4315: 1.5 mm) Range 0.8 to 2.5, step
0.1.
ctrl_iec_z
4
IEC inlet: cutout’s bottom edge above the bay floor Range 0 to
30, step 0.5.
ctrl_pocket_clear
2
Clearance around the inlet’s body and the jacks’ bodies in their
tunnels, per side Range 0.5 to 6, step 0.5.
ctrl_back_skin
5
Back wall left behind the two tunnels (it is thinned to the panel
thickness only round the cutouts) Range 2 to 17, step 0.5.
ctrl_panel_margin
2.5
Thinned panel’s margin round each cutout (or round the jacks’
array), for the inlet’s and keystones’ latches Range 1 to 8, step
0.5.
ctrl_jack_kind
"keystone"
Jacks: snap-in keystone modules (3.5 mm and 1/4” jack inserts are
sold for keystone panels), or round holes for panel-mount jacks held by
a nut Choices: keystone, round.
ctrl_jacks
[1, 2]
Jacks: [rows, columns]
ctrl_keystone_cutout
[14.5, 16.2]
Keystone cutout [width, height] (the usual 14.5 x 16.2; the latch is
at the top)
ctrl_jack_hole
9.7
Round jack hole (1/4” jacks with a 3/8” bushing: 9.7; 3.5 mm jacks:
about 6.2; check yours) Range 3 to 16, step 0.1.
ctrl_jack_pitch
[16.5, 22]
Jack pitch [across, up]
ctrl_jack_panel
2
Jack panel thickness (keystones latch on 1.5 to 2.2 mm; panel jacks
take up to their thread length) Range 0.8 to 5, step 0.1.
ctrl_jack_z
0
Jacks: bottom row’s centre above the bay floor; 0 = centred in the
tunnel’s straight sides Range 0 to 60, step 0.5.
ctrl_knockouts
true
Close the pass-through with knock-out walls (tap them out when the
motor’s leads go through; passthrough_knockouts does this for the other
options)
ctrl_posts
"grid"
Posts for the boards: a grid, a list of positions (from a board’s
own holes), both, or none Choices: grid, list, both, none.
ctrl_grid
[5, 2]
Grid: [rows (front to back), columns (left to right)]
ctrl_grid_pitch
[25.4, 25.4]
Grid pitch [left to right, front to back] (1” = 25.4, ten 0.1”
perfboard holes, so any perfboard can be drilled to fit)
ctrl_grid_offset
[0, 0]
Grid centre’s offset from the middle of the bay floor [x, y]
ctrl_post_list
[[0, 0], [46, 0], [0, 66], [46, 66]]
List: post positions [[x, y], …], as measured between a board’s
mounting holes (here a 50 x 70 mm prototyping board, holes 46 x 66
apart; check yours) Edit in the file; not shown in the
Customizer.
ctrl_list_origin
[12, 20]
List: where its [0, 0] falls, from the bay floor’s front left
corner
ctrl_post_d
8
Post diameter Range 5 to 14, step 0.5.
ctrl_post_h
6
Post height: board underside above the floor Range 2 to 30, step
0.5.
ctrl_post_hole
"insert"
Post hole: an M3 heat-set insert, or a pilot for a thread-forming
screw for plastics (M3 or #4) Choices: insert, screw.
ctrl_insert_d
4.6
Heat-set insert hole (M3) Range 3 to 6, step 0.05.
ctrl_pilot_d
2.5
Pilot hole for a thread-forming screw Range 1.5 to 4, step
0.05.
ctrl_hole_depth
8
Hole depth from the post’s top (may run on into the floor) Range
3 to 15, step 0.5.
mezz_posts
"list"
Mezzanine (part ctrl_mezzanine): a plate screwed down to the floor
posts, carrying new posts for a board that doesn’t fit them; for a base
already printed. Its new posts: a grid or a list, in the same frame as
the floor’s (from the bay floor’s front left corner) Choices: grid,
list.
mezz_grid
[2, 2]
mezz_grid_pitch
[40, 60]
mezz_grid_offset
[0, 0]
mezz_post_list
[[0, 0], [40, 0], [0, 55], [40, 55]]
Edit in the file; not shown in the Customizer.
mezz_list_origin
[15, 30]
mezz_plate_t
3
Mezzanine plate thickness Range 2 to 8, step 0.5.
mezz_lift
0
Lift: legs under the plate at the floor posts (0 = plate straight on
the posts) Range 0 to 40, step 0.5.
mezz_margin
6
Margin of plate around the posts and holes Range 3 to 20, step
0.5.
mezz_screw_hole
3.4
Screws down into the floor posts: clearance hole Range 2 to 5,
step 0.1.
mezz_screw_head
6
Head diameter of those screws (to keep the new posts clear of them)
Range 4 to 10, step 0.5.
10.23 Attached bay
Parameter
Default
Description
attached_lid_type
"none"
Attached bay’s lid: none (the default, since cords from the machine
may lie over the bay’s edge), hinged (on the edge set by
base_lid_hinge), or lift-out Choices: none, hinged,
lift-out.
attach_screw_spec
"M5"
Joint screws: socket-head cap screws through the base’s right end
wall, from inside the machine cavity, into heat-set inserts in the bay’s
inner wall
attach_screw_hole
5.5
Joint screw clearance hole Range 3 to 8, step 0.1.
attach_head_d
9.5
Joint screw head counterbore, in the base’s end wall from the cavity
side Range 5 to 14, step 0.1.
attach_head_seat
8
Wall left under each screw head Range 4 to 15, step
0.5.
attach_insert_d
6.4
Heat-set insert hole in the bay’s inner wall (M5) Range 3 to 9,
step 0.05.
attach_insert_depth
10
Heat-set insert hole depth Range 5 to 14, step 0.5.
attach_screw_inset
12
Joint screws: distance in from the machine cavity’s front and back
walls Range 6 to 40, step 0.5.
attach_dowel_depth
10
Dowels (rod_d rod, two): depth into each part Range 5 to 13,
step 0.5.
attach_dowel_press
0.1
Dowel hole in the base: press fit (diameter under rod_d) Range 0
to 0.5, step 0.05.
attach_dowel_slip
0.2
Dowel hole in the bay: slip fit (diameter over rod_d) Range 0 to
0.6, step 0.05.
attach_web
4
Bay’s top web between the joint and its lid rabbet Range 2 to
10, step 0.5.
10.24 Cord pass-through
Parameter
Default
Description
cord_hole_width
46
Cord pass-through width (wide enough for both plugs’ cords side by
side)
cord_hole_height
36
Cord pass-through height (without gable)
passthrough_knockouts
false
Close both ends of the pass-through with knock-out walls (tap them
out with a punch when you fit the outlet)
passthrough_knockout_t
1.6
Knock-out wall thickness Range 0.8 to 3, step 0.1.
passthrough_score_depth
0.6
Score groove around each knock-out wall’s edge, on its tunnel side:
depth (deeper = easier to knock out) Range 0.2 to 1.5, step
0.1.
passthrough_score_w
0.8
Score groove width Range 0.4 to 2, step 0.1.
passthrough_cover
false
Make a removable cover for the pass-through (part
passthrough_cover), pushed into its compartment end
passthrough_cover_depth
6
Cover: depth of the plug into the tunnel Range 3 to 15, step
0.5.
10.25 Split
Parameter
Default
Description
split_part
"both"
Which part to render when split Choices: both, left,
right.
split_spread
30
Separation between the two halves when both are shown
split_balance
true
Put the split where the two halves, the left one’s dovetail keys
included, come out the same length (else at the middle)
split_clearance
0.1
Clearance in the joint, per face
key_neck
8
Dovetail key width at the cut line (neck) Range 4 to 16, step
0.5.
key_flare_angle
30
Dovetail flare, per side, in degrees; steeper = less pull-apart
play
key_depth
8
Dovetail key length, past the cut line into the right half Range
4 to 16, step 0.5.
key_ys
[]
Key positions in Y; empty = automatic (floor keys between plate
rows, one centered in the back wall) Edit in the file; not shown in
the Customizer.
serrations
true
Vertical V-serrations across the front wall’s joint faces
serration_pitch
3
Serration pitch (ridge to ridge) Range 2 to 6, step
0.1.
serration_height
1.5
Serration height (ridge tip beyond the cut line); pitch / 2 gives a
90-degree V
serration_setback
2.5
Solid wall kept between the serrations and each face of the front
wall (outer skin and cavity side)
serration_top_gap
3
Serrations stop this far below the bed ledge Range 1 to 10, step
0.5.
serration_top_clear
0.5
Extra clearance at the top of each groove, so the ridges never
bottom out
10.26 Body
Parameter
Default
Description
rim_width
9
Top rim: outer face to seat/rabbet edge, front, left and right
Range 5 to 20, step 0.5.
end_wall
22.225
End wall thickness at the bottom, left and right (7/8” =
22.225)
base_depth
0
Base depth front to back: a standard class, so bases of a class
share extensions; auto = the smallest that fits Choices: 0:Auto,
200:200 mm, 230:230 mm, 250:250 mm.
back_rim_width
0
Top rim: back of the bed seat to outer back face (0 = from the hinge
and base_depth; set it to override the class)
back_rim_thin
12
With no hinges: the back rim before rounding up to the depth class
Range 8 to 40, step 0.5.
hinge_back_skin
5
With automatic back rim: solid behind the hinge’s rear edge
Range 2 to 15, step 0.5.
bottom_thickness
12.7
Bottom thickness (the base may be raised above this to bring the bed
to ext_height)
inner_depth
70
Cavity depth below the top surface
divider_web
4
Solid web at the top between the bed seat and the lid rabbet
Range 2 to 10, step 0.5.
outer_rounding
5
Outer edge rounding (top and vertical edges) Range 0 to 10, step
0.5.
10.27 Bed seat
Parameter
Default
Description
bed_clearance
0.75
Clearance between bed and seat wall, per side
bed_ledge
8
How far the bed rests on the ledge around the machine cavity
Range 3 to 15, step 0.5.
rabbit_depth
4
Depth of the bed seat and lid rabbet below the top surface Range
2 to 8, step 0.1.
10.28 Back wall lightening
Parameter
Default
Description
lighten_back_wall
true
Hollow the back wall between the hinges
back_skin
17
Back wall thickness left behind the tunnels Range 6 to 40, step
0.5.
back_top_skin
6
Solid material above the tunnel peaks Range 2 to 20, step
0.5.
tunnel_width
30
Target tunnel width
tunnel_web
6
Web between tunnels
hinge_tunnel_margin
7.5
Extra solid kept beyond each side of the hinge footprint
split_keepout
15
Solid zone kept on either side of the split, from the cut line
10.29 Extension pegs
Parameter
Default
Description
ext_peg_holes
true
Holes in the base rim for the extension pegs
ext_peg_style
"insert"
Pegs: insert (separate printed pegs, part ext_pegs, printed lying
down), pin (cut from rod_d rod), or molded into the lip (as before v20)
Choices: insert, pin, molded.
peg_d
4
Peg diameter (printed pegs) Range 3 to 8, step 0.1.
peg_len
3
Peg length below the lip Range 1.5 to 6, step 0.1.
peg_hole_d
4.4
Hole diameter in the base (for printed pegs; pins use rod_d +
0.2)
peg_lip_clearance
0.2
Peg hole in the lip, over the peg diameter (the peg’s crush ribs
make the press fit)
pin_lip_interference
0.1
Metal pins: press fit in the lip, hole under the rod diameter
peg_hole_depth
3.5
Hole depth in the base
back_peg_xs
[16, 160]
Back-rim peg positions (X), from the base’s left face: standard for
every machine, so back extensions fit any base of their class; keep
clear of the hinges and the split
left_peg_ys
[35, 150]
Left-rim peg positions (Y)
right_peg_ys
[35, 150]
Right-rim peg positions (Y), for future right-side extensions; []
for none
10.30 Corner dovetails
Parameter
Default
Description
ext_dt_neck
6
Dovetail width at the mating face Range 3 to 12, step
0.5.
ext_dt_head
9
Dovetail width at its head Range 4 to 16, step 0.5.
ext_dt_depth
4
Dovetail depth into the mating wall Range 2 to 10, step
0.5.
ext_dt_clearance
0.2
Dovetail clearance per face
10.31 Left lip
Parameter
Default
Description
lip_edge_round
2
Radius of the rounded top edge along the lip front (also the free
edges of an extended back lip) Range 0 to 5, step 0.5.
lip_fillet
5
Radius of the inside corner where the lip front meets the body (also
an extended back lip’s corners) Range 0 to 15, step 0.5.
10.32 Back lip
Parameter
Default
Description
back_lip_extend
true
Run the back lip on past a short back extension, over the base’s
back rim, to reach the last back peg hole
back_lip_peg_margin
10
How far the lip runs past the last peg’s center Range 6 to 30,
step 0.5.
10.33 Lollipop hinge
Parameter
Default
Description
hinge_flange_diameter
29
Hinge flange diameter Range 15 to 50, step 0.1.
hinge_flange_thickness
3
Hinge flange thickness Range 1 to 8, step 0.1.
hinge_thickness
8
Hinge body depth below the top surface Range 3 to 20, step
0.1.
hinge_inner_diameter
27
Hinge body diameter Range 10 to 50, step 0.1.
hinge_pin_thickness
8
Hinge pin thickness (X) Range 3 to 15, step 0.1.
hinge_pin_height
8
Hinge pin height (Z) Range 3 to 15, step 0.1.
hinge_pin_extension
25
Hinge pin extension Range 5 to 60, step 0.5.
hinge_pin_square_projection
10
Hinge pin square projection Range 2 to 30, step 0.5.
hinge_pin_allowed_projection
2
Hinge pin allowed square projection into the bed seat Range 0 to
6, step 0.1.
hinge_pin_internal_length
15
Hinge pin internal length Range 5 to 40, step 0.5.
hinge_pin_sweep_depth
1
Extra depth below the pin for its corner to sweep through Range
0 to 4, step 0.1.
hinge_mounting_hole_diameter
5
Hinge mounting hole diameter Range 2 to 10, step 0.1.
hinge_mounting_hole_offset
9.5
Mounting hole center, inward from the flange’s back edge
10.34 Barrel hinge
Parameter
Default
Description
barrel_d
15.2
Barrel hinge (hinge_type = “barrel”, from vintage portable cases):
barrel diameter Range 8 to 30, step 0.05.
barrel_h
17.5
Barrel height (its top was flush with the case) Range 8 to 40,
step 0.05.
barrel_pin_z
11.8
Arm’s pin axis above the barrel’s bottom, arm level Range 3 to
30, step 0.05.
barrel_pivot_z
14.3
Cross pin (the arm’s pivot) above the barrel’s bottom Range 3 to
30, step 0.05.
barrel_pivot_dy
4.5
Cross pin in front of the barrel’s axis, toward the bed Range 0
to 10, step 0.05.
barrel_reach
30
Barrel axis to the pin’s tip, arm level Range 15 to 60, step
0.1.
barrel_block
[16.4, 9.3, 7.1]
Arm’s block: length (along the arm), height, width
barrel_pin
[6.85, 18.8]
Arm’s pin: diameter, and length from the block to the tip
barrel_tilt
65
How far the arm tips back Range 30 to 110, step 1.
barrel_clear
0.3
Clearance round the barrel and the arm’s swing Range 0.1 to 1,
step 0.05.
barrel_screw
[35.4, 4.78, 11, 7]
Screw: length overall, head height, head diameter, thread
diameter
barrel_washer
[1.5, 13.7]
Washer under the screw head: thickness and outside diameter
barrel_tap_depth
6
Depth of the barrel’s tapped hole the screw may use Range 3 to
12, step 0.5.
10.35 Printed hinge
Parameter
Default
Description
ph_pin_d
0
Steel pin into the bed’s hinge hole: diameter, just under the
hole’s; 0 = from the machine profile (9/32” for the 99K, 6 mm for the
Kenmore 158-14001) Range 0 to 12, step 0.01.
ph_pin_engage
0
How far the pin enters the bed’s hole; 0 = from the machine profile.
Ignored when ph_pin_len is set Range 0 to 30, step 0.5.
ph_pin_len
0
Stock length of the pins, for a bought dowel pin (0 = cut to the
length the console gives): the pin goes into the bed’s hole by whatever
is left past the arm; the console gives the lengths that fit the hole’s
depth Range 0 to 80, step 0.5.
ph_pivot_len
0
Stock length of the pivot rods, for a bought dowel pin (0 = the
block’s width, set by ph_cheek): the block’s cheeks are widened or
narrowed to suit Range 0 to 60, step 0.025.
ph_pin_embed
16
Length of the pin pressed into the arm Range 8 to 30, step
0.5.
ph_pivot_d
6.35
Steel pivot rod, running along the back through the block and the
arm: diameter Range 3 to 12, step 0.01.
ph_press
0
Pivot rod’s press fit in the block: printed hole diameter minus rod
diameter (try part printed_hinge_test) Range -0.4 to 0.4, step
0.05.
ph_pin_press
0
Pin’s press fit in the arm: printed hole diameter minus pin diameter
(try part printed_hinge_test) Range -0.4 to 0.4, step
0.05.
ph_slip
0.3
Running fit: the arm’s pivot hole is this much larger than the rod
Range 0 to 1, step 0.05.
ph_wall
4
Plastic around the rods in the arm Range 2.5 to 8, step
0.5.
ph_arm_w
14
Arm width (X) Range 8 to 30, step 0.5.
ph_cheek
6
Block cheeks either side of the arm (X) Range 3 to 15, step
0.5.
ph_clear
0.4
Clearance between the moving arm and the block Range 0.2 to 1.5,
step 0.05.
ph_web
4
Base web left between the bed seat and the hinge recess Range 2
to 10, step 0.5.
ph_head_d
9.5
Screw head counterbore from under the base, for a pan or socket head
(#8 pan: 8.2 mm) Range 5 to 16, step 0.1.
ph_floor
3
Block floor under the arm Range 2 to 8, step 0.5.
ph_recess_clear
0.2
Fit of the block in its recess, each side Range 0 to 0.6, step
0.05.
ph_stop_angle
100
Tilt-back stop: a tail on the arm, behind the pivot, comes to rest
in the block at about this angle (0 = no stop, 45 to 110). 100 matches a
Singer lollipop hinge’s knuckle; the machine passes its balance point
(about 55 degrees on a 99K) well before, and past about 75 degrees the
base itself starts to tip up unless the machine is held or braced
Range 0 to 110, step 1.
ph_tail
12
Tail length behind the pivot (longer: less force on the stop, deeper
block) Range 6 to 25, step 0.5.
ph_min_cover
2.5
Least plastic over the rods where the arm and cheeks are cut down to
the rim Range 1.5 to 5, step 0.25.
ph_test_step
0.1
Rod-fit test (part printed_hinge_test): the step between its five
holes, around ph_pin_press and ph_press (0.05 for a finer second bar)
Range 0.02 to 0.2, step 0.01.
10.36 Hinge nut traps
Parameter
Default
Description
hinge_nut_spec
"#8-32"
Nut for the hinge screws (BOSL2 spec, e.g. “#8-32”, “M4”)
hinge_nut_width
0
Nut width across flats; 0 = from the spec Range 0 to 20, step
0.05.
hinge_nut_depth
21
Depth of the nut’s upper face below the top surface Range 8 to
60, step 0.5.
hinge_nut_bridge
0.2
Sacrificial bridge over the nut trap (0 = none; drill through after
printing)
hinge_nut_tool_tip
3.0
Nut tool (part hinge_nut_tool): tip diameter, to fit the nut’s bore
(a nylon-insert locknut’s insert: 1/8”) Range 1.5 to 6, step
0.05.
10.37 Hinge coupon
Parameter
Default
Description
hinge_coupon_margin
12
Solid margin around the hinge flange (room for the corner
screws)
hinge_coupon_floor
4
Floor left under the deepest hinge cut Range 2 to 10, step
0.5.
hinge_coupon_screw_d
4.6
Corner holes for #8 flat-head wood screws: clearance hole
hinge_coupon_head_d
8.4
Corner holes: countersink diameter at the top face
Hole centers [along, across] from the plate center (0.889” pitch,
staggered 0.094”) Edit in the file; not shown in the
Customizer.
plate_hole_bridge
0.3
Sacrificial layer over each screw hole at the pocket ceiling (0 =
none); drill through
plate_pocket_clearance
0.5
Clearance around the plate in its pocket, per side
plate_standoff
1.0
How far the plate sits up inside its pocket, so screw heads stay off
the table
plate_screw_clearance
4.6
Screw clearance hole diameter (#8)
plate_nut_spec
"#8-32"
Nut for the plate screws (BOSL2 spec)
plate_nut_width
0
Nut width across flats; 0 = from the spec Range 0 to 20, step
0.05.
plate_nut_trap_depth
3.5
Nut trap depth into the cavity floor
plate_wall_margin
8
Minimum distance from the cavity walls to the plate edge Range 2
to 20, step 0.5.
10.39 Nut fit
Parameter
Default
Description
nut_clearance
0.15
Extra clearance added to nut width (applied to each side)
10.40 Casting reliefs
Parameter
Default
Description
relief_clearance
1
Clearance below the casting in a relief (the reliefs themselves come
from the machine profile) Range 0 to 4, step 0.1.
relief_margin
2
Extra length added at each end of a relief Range 0 to 10, step
0.5.
10.41 Foot-locating rig
Parameter
Default
Description
rig_height
80
Parts foot_rig_left and foot_rig_right: a thin box that fits round
the bed, to stand the machine on paper and print its inked feet. Wall
height Range 30 to 150, step 1.
rig_wall
2.4
Wall thickness Range 1.2 to 5, step 0.2.
rig_rim
10
Floor rim, inward from the wall (it lies under the bed’s edge)
Range 5 to 25, step 0.5.
rig_floor
2
Floor rim thickness Range 1 to 5, step 0.2.
rig_lap
15
Overlap of the splice tabs past the split, each way Range 8 to
30, step 1.
rig_bolt_d
3.4
Splice bolt holes (M3) Range 2 to 5, step 0.1.
rig_screw_d
3.5
Screw holes through the floor rim, to fix the rig to a board
Range 2 to 6, step 0.1.
rig_mark_in
5
Marking holes in the floor rim, this far in from the bed’s edges at
each corner and at the split, for a pencil or awl Range 3 to 9, step
0.5.
rig_mark_d
1.6
Range 0.8 to 3, step 0.1.
rig_bar_in
100
Floor bars across the rig, this far in from each end of the bed
(mm), to keep each half square; set them where no foot can land (0 =
none) Range 0 to 250, step 1.
rig_bar_w
10
Floor bar width, and the height of the stiffening rib along it
Range 5 to 20, step 0.5.
rig_bar_rib
5
Range 0 to 15, step 0.5.
rig_crossbar
false
A floor bar across the split as well (it covers the paper
there)
rig_tie
true
Breakaway tie across each half’s open end at the split, holding the
walls while printing; snap it off at its thin necks before bolting the
halves together
rig_tie_w
6
Range 3 to 12, step 0.5.
rig_ears
false
Mouse ears: thin discs at each half’s corners, to hold them down
while printing; cut off after. Off by default: a slicer’s own mouse-ear
brim (Bambu Studio’s brim type “Mouse ear”) does the same without brims
round the discs
rig_ear_d
16
Range 8 to 30, step 1.
rig_ear_h
0.4
Range 0.2 to 1, step 0.1.
10.42 Tilt prop
Parameter
Default
Description
tilt_prop_h
0
Part tilt_prop: a stand on the table behind the base that catches
the machine’s arm when it is tipped back to about 90 degrees, for
hands-free servicing. Height of the arm’s underside above the table
there, mm; 0 = from the machine profile (99K: 6”) Range 0 to 300,
step 1.
tilt_prop_top
"profile"
Top: from the profile, a cradle (for a round arm), or flat and level
(for anything else) Choices: profile, cradle, flat.
tilt_prop_r
0
Cradle radius (the arm’s radius plus a little), mm; 0 = from the
profile (99K: 1”) Range 0 to 60, step 0.5.
tilt_prop_flat
50
Flat top: depth front to back, mm Range 20 to 120, step
1.
tilt_prop_w
38.1
Cradle width, along the arm (1.5”) Range 20 to 80, step
0.5.
tilt_prop_foot
[80, 110]
Foot: width along the arm, and depth front to back Range 40 to
200, step 1.
10.43 Test parts
Parameter
Default
Description
test_top_h
12.7
Test parts: height of the top slices
test_floor_extra
3
Test parts: height of the base bottom slice above the cavity
floor
test_coupon_w
40
Test parts: width of the dovetail coupon (X)
test_slice_w
112
Test parts: width of the center slice (X); covers the plates at
112
test_stub_w
20
Test parts: full-height wall stubs either side of the joint in the
center slice
test_hinge_w
40
Test parts: size of the hinge block (X), centered on the left
hinge
test_split_gap
10
Gap between the two halves of split test parts
test_passthrough_whole
false
Pass-through test: print it whole, as in the base, the tunnel sealed
between its two knock-out walls (leave it as one object in the slicer:
split into shells, the tunnel’s lining becomes a solid of its own),
rather than cut in two down the divider
test_corner_w
0
Front corner test: width (X) of each corner piece, from the base’s
end; 0 = wide enough for a 40 mm logo (or the logo, if wider) and the
ruler below it Range 0 to 150, step 1.
split_test_h
30
Split test (part split_test): height of the front-wall stubs; 0 =
full height Range 0 to 100, step 1.
split_test_w
25
Split test: width either side of the split line Range 10 to 60,
step 1.